editor
699
edits
Router - TP-Link - TD-W9980: Difference between revisions
m
clean up, typos fixed: ie, → i.e.,, 100Mbps → 100Mbit/s (3)
CrazyTeeka (talk | contribs) mNo edit summary |
m (clean up, typos fixed: ie, → i.e.,, 100Mbps → 100Mbit/s (3)) |
||
| (19 intermediate revisions by 2 users not shown) | |||
|
[[File:TP-Link_TD-W9980.png]]
=Specs=
*VDSL2/ADSL2+ Modem Router, supporting up to 100Mbit/s broadband speeds.
*Simultaneous 2.4 GHz 300Mbit/s and 5 GHz 300Mbit/s WiFi.
*4 Gigabit Ports.
*Ethernet WAN (EWAN) for connecting to VDSL/ADSL modems.
*WiFi On/Off Switch allows users to simply turn their wireless radio on or off.
*Supports IPv6.
*Annex A/B/L/M.
*Bit Swap.
*SRA.
=Firmware=
Latest firmware is here: [http://uk.tp-link.com/support/download/?model=TD-W9980&version=V1 TP-Link TD-W9980 Firmware]
=Factory Reset=
*Method 1: With the router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it.
*Method 2: Login to router, click "System Tools", click "Factory Defaults", click "Restore", router will reboot with factory defaults.
=Default Username/Password=
{|class="wikitable"
!colspan="2"|Default Username/Password
|-
!IP:
|192.168.1.1
|-
!Username:
|admin
|-
!Password:
|admin
|}
=Quick Start - ADSL Modem Router=
#Click "Quick Setup".
#Start - Click "Next".
#Region and Time Zone - Choose "United Kingdom" and "(GMT)", click "Next".
#Operation Mode - Choose "xDSL Modem Router Mode", click "Next".
#Select ISP - From ISP List choose "ADSL_BT", click "Next".
#PPPoA - Enter broadband username and password, click "Next".
#Wireless 2.4 GHz - Change WiFi SSID and Password (Optional), click "Next".
#Wireless 5 GHz - Change WiFi SSID and Password (Optional), click "Next".
#Confirm - Check settings then click "Save".
=Quick Start - VDSL Modem Router=
#Click "Quick Setup".
#Start - Click "Next".
#Region and Time Zone - Choose "United Kingdom" and "(GMT)", click "Next".
#Operation Mode - Choose "xDSL Modem Router Mode", click "Next".
#Select ISP - From ISP List choose "VDSL_AAISP", click "Next".
#PPPoE - Enter broadband username and password, click "Next".
#Wireless 2.4 GHz - Change WiFi SSID and Password (Optional), click "Next".
#Wireless 5 GHz - Change WiFi SSID and Password (Optional), click "Next".
#Confirm - Check settings then click "Save".
=Quick Start - PPPoE Router=
#Click "Quick Setup".
#Start - Click "Next".
#Region and Time Zone - Choose "United Kingdom" and "(GMT)", click "Next".
#Operation Mode - Choose "Wireless Router Mode", click "Next".
#Ethernet WAN Type - Choose "PPPoE", click "Next".
#PPPoE - Enter broadband username and password, click "Next".
#Wireless 2.4 GHz - Change WiFi SSID and Password (Optional), click "Next".
#Wireless 5 GHz - Change WiFi SSID and Password (Optional), click "Next".
#Confirm - Check settings then click "Save".
=Bridge - ADSL Modem=
#Click "Network".
#Click "WAN Settings".
#Click "Add".
#DSL Modulation Type: ADSL
#VPI: 0
#VCI: 38
#Connection Type: Bridge
#Click "Save".
=Bridge - VDSL Modem=
#Click "Network".
#Click "WAN Settings".
#Click "Add".
#DSL Modulation Type: VDSL
#Enable VLAN ID: ✓
#VLAN ID: 101
#Connection Type: Bridge
#Click "Save".
==Bridging Notes==
#Firmware TD-W9980_V1_150507 07/05/15 does not support *at least* 1508 byte frames so as to allow RFC4638 PPPoE to a connected device. i.e., 1500 byte MTU is not possible when in bridge mode.
#*AAISP contacted TP-Link regarding this 2015-09-12
[[Category:3rd Party Routers|TP Link]]
| |||