Stopping Open DNS - ZyXEL P660R-D1: Difference between revisions

← Older edit

Stopping Open DNS - ZyXEL P660R-D1 (view source)

Revision as of 23:59, 17 August 2018

489 bytes added , 17 August 2018

→‎See also: clean up

Reedy

editor

699

edits

Revision as of 22:11, 6 January 2014 (view source) AA-Andrew (talk \| contribs) mNo edit summary ← Older edit		Latest revision as of 23:59, 17 August 2018 (view source) Reedy (talk \| contribs) (→‎See also: clean up)
(11 intermediate revisions by 2 users not shown)
[[File:P660rd1.png\|link=Router - ZyXEL P660R-D1]] The factory setting for this router on older firmware is for DNS to be open on the WAN IP as well as the LAN IP. This will be changed when configured by AAISP, but if it is configured from new, or reset, then WAN side DNS may need to be disabled. ~~This can be done from the web interface and '''setting DNS Access Status to LAN'''. Go to:~~ > Advanced - Remote MGMT - DNS - LAN▼ =Changing DNS Settings via the Web Interface= [[File:Zyxeld1-opendns-3.png]]▼ This can be done from the web interface and '''setting DNS Access Status to LAN'''. Go to: ▲ > Advanced - Remote MGMT - DNS ~~- LAN~~ Then re-test from the Control Pages: https://clueless.aa.net.uk/dnsresolvers.cgi ▲[[File:Zyxeld1-opendns-3.png]] The LAN/WAN here are relating to the LAN/WAN IP addresses, not the LAN/WAN interfaces. =Changing DNS Settings via Telnet= If you still can't access the router web pages, then you can do this via telnet by running the following commands:▼ View the current access settings (for all services) sys server load ▼ sys server ~~access dns 2~~ disp▼ To make the change to the access: sys server load sys server access dns 1 sys save▼ Note: Allowed access type: 0:ALL, 1:None, 2:LAN IP only, 3:WAN IP only =FAQ= ==The DNS checker is saying DNS is still open== If you have ~~Static~~publicly ~~Routes~~routed ~~setup,~~IP ~~then~~addresses ~~disable~~on ~~DNS~~the ~~completely~~LAN inside of the ~~above~~router ~~settings~~then ~~page.~~you ~~Even~~may ~~though~~wish to disable the ~~setting~~resolver iscompletely ~~set~~instead toof ~~LAN,~~restricting ~~with~~it ato ~~static~~the LAN ~~route~~IP, as the ~~DNS~~LAN IPs will be still be ~~open~~accessible ~~due~~from ~~to a~~the ~~bug~~outside ~~in the router~~world. ==What is the IP address of the router?== Sometimes the webserver on the router stops working, try turning the router off and on again. ==~~Changing~~Does this ~~via~~apply ~~Telnet~~to other routers?== This also applies to the P-660HW-T1 v2 Router, and probably other ZyXELs▼ ▲If you still can't access the router web pages, then you can do this via telnet by running the following commands: ▲ sys server load ▲ sys server access dns 2 ▲ sys save ▲This also applies to the P-660HW-T1 v2 Router ==~~Also~~See ~~see:~~also== [[:Category:Open DNS Resolvers]] [[~~Router_~~Router -~~_ZyXEL_P660R~~ ZyXEL P660R-D1]] [[Category:Open DNS Resolvers]] [[Category:~~Router~~AA Routers]] [[Category:3rd Party Routers]]