Category:Incoming L2TP: Difference between revisions

From AAISP Support Site
mNo edit summary
mNo edit summary
Line 1: Line 1:
__NOTOC__<indicator name="L2TP">[[File:Menu-L2TP.svg|link=:Category:L2TP|30px|Back up to the L2TP Category]]</indicator>
__NOTOC__<indicator name="L2TP">[[File:Menu-L2TP.svg|link=:Category:L2TP|30px|Back up to the L2TP Category]]</indicator>


=L2TP from Customers to AAISP=
=L2TP from Customers to AAISP=
This is used to connect in to AAISP over a third-party internet connection. This gives you your usual AAISP IP (4 and 6) blocks and access to the internet as if you were conencted via a normal DSL circuit.
This is used to connect in to AAISP over a third-party internet connection. This gives you your usual AAISP IP (4 and 6) blocks and access to the internet as if you were conencted via a normal DSL circuit.

Revision as of 12:35, 9 May 2016

L2TP from Customers to AAISP

This is used to connect in to AAISP over a third-party internet connection. This gives you your usual AAISP IP (4 and 6) blocks and access to the internet as if you were conencted via a normal DSL circuit.

  • Hostname: l2tp.aa.net.uk
  • Plain L2TP without any IPsec
  • MSCHAPv2 authentication


Some Notes from customers setting up L2TP IN to AAISP:

FireBrick FB2500/2700 Fully Loaded

The FireBrick can connect as an L2TP client for fallback and for its main connection. One thing to watch out for is making sure that the FB doesn't set its own gateway to be the tunnel (which would logically send tunnel packets up the tunnel, which is horrid). You can get around this by using separate routing tables.

This example is for L2TP being the main connection:

<interface name="WAN"
           port="WAN1"
           table="1"
           comment="DHCP client">
<l2tp>
 <outgoing name="AAISP"
           ip="90.155.53.19"
           graph="AAISP"
           table="1"
           payload-table="0"
           username="example@a"
           password="secret"
           tcp-mss-fix="true"
           comment="L2TP tunnel to AAISP"/>
</l2tp>

You can set to fall back to NAT if the tunnel is down. Traffic on routing table 0 won't have a default gateway if the L2TP is down, so will match this rule set that has target interface "nowhere":

<rule-set name="Fallback"
          target-interface="nowhere"
          no-match-action="continue"
          comment="NAT fallback if can't establish L2TP">
 <rule name="NAT"
       set-nat="true"
       set-table="1"
       action="accept"/>
</rule-set>

If the L2TP is being used for fallback, you are probably better off setting the routing table for the L2TP to something other than 0. Remember firewall rules only apply to single routing tables.

RouterBoard

Connecting to L2TP with a RouterBoard was pretty seamless - put in the L2TP server IP, username and password and it just connects. Have to mess about with IP / Route and NAT / masquerading a bit to get devices behind the RouterBoard online but that all depends on whether you have an additional IP block and what you want to do with it anyway.

Apple OSX

An Apple computer can be used to create an L2TP connection in to AAISP, here's how:

  • Apple Menu - Settings - Network
  • Click the + Icon
  • Create a new VPN Interface with Type L2TP over IPSec

L2tp-osx-newconnection.png

  • In the Authentication settings set the Password
  • For ease of use Tick 'Show VPN status in menu bar
  • Optionally, in the Advanced Settings Tick, 'Send all Traffic over VPN connection'
  • Then Connect

L2tp-osx-connected.png

  • To Disconnect, click Disconnect

You can use the new icon in the Status bar (Up by the clock, to connect and disconnect the connection

L2tp-osx-ipsecmenu.png

VPN Connection - IPsec Error

Use this at your own risk. The notes below involves editing/creating system files, and whilst 'worked for us' may not work for you.

By default, OSX requires the L2TP connection to use IPSec encryption. At the moment the AAISP service is just plain L2TP and does not offer encryption.

L2tp-osx-ipsecerror.png

To enable OSX to connect without IPSec, then the /etc/ppp/options file needs to be edited. A simple way of doing this is as follows:

  1. Use the Search icon to search for Terminal

Osx-finding-terminal.png

and then enter in:

echo "plugin L2TP.ppp" > options
echo "l2tpnoipsec" >> options
sudo mv options /etc/ppp

If the mv (move) fails, then you may already have a /etc/ppp/options file, in this case it would need to be edited manually.

To undo this change delete the /etc/ppp/options file.

Windows 7

Connecting with Windoze 7 was almost as easy except that the default connection settings don't work. You have to edit the connection properties and on the Security tab change 'Type of VPN:' to 'Layer 2 Tunneling Protocol with IPsec (L2TP/IPSec)' otherwise it only tries PPTP, and change 'Data encryption:' to 'Optional encryption (connect even if no encryption)' as it doesn't like A+A's certificate (because RevK declines to use a root certification authority recognised by Microsoft, or is it that Microsoft declines to recognise the root certification authority chosen by RevK). I guess the alternative would probably be to add the root certificate to the machine in question. Anyway, with those two changes it works fine.

Watch out if you are using IPv6. It seems that Win7 negotiates a non-routable IPv6 address with the LNS. You have to discard this address and manually configure one of your routed IPv6 addresses. ipconfig /release6 is your friend here.

Cisco Routers

Cisco routers running IOS 12.3(2)T and later support L2TP client initiated tunneling which allows the router to establish an L2TP tunnel to A&A's L2TP server.

Most of the information required was gleaned from here: [1] plus a bit of trial and error and some packet capturing of good and bad L2TP sessions.

I have tested this on a Cisco 837 router running 12.3(11)YZ2, a 2821 running 12.4(15)T10 SPServices and a 2801 running 12.4(24)T3 ADVIPServices

Caveats:

- You will need to sanity check routing in your particular environment. This is especially important if you choose to use ppp ipcp route default on the l2tp tunnel. It's safest to make sure that you have a static route set to the L2TP server.

- I haven't tested this for IPV6 yet.

- This is "early release" information - I haven't yet used this in anger over a long period of time but will try to remember to come back and update if I find any major issues.

- This config snippet contains no security settings - be sure to configure some!

- I've used the IP address of the L2TP server rather than the DNS address - this is obviously at risk of change .

- You need to be running IP CEF on the router

Config:

Replace <whatever> with the appropriate information for your connection

ip cef
l2tp-class lc-aaisp

pseudowire-class pc-aaisp
 encapsulation l2tpv2
 protocol l2tpv2 lc-aaisp
 ip local interface <interface that l2tp connection should go out from>

interface Virtual-PPP9797
 shutdown
 ip address negotiated
 no cdp enable
 ppp authentication chap callin
 ppp chap hostname <l2tp line login eg stzzz@a.2>
 ppp chap password 0 <site password>
 ppp direction callout
 ppp pap refuse
 pseudowire 90.155.53.19 10 pw-class pc-aaisp
 

Once the interface is configured you can issue a no shut on it to bring it up.

Debugging:

debug ppp authentication and debug ppp negotiation are your friends... In particular if you see "Circuit ID not set - contact support" in the authentication debug, contact A&A support to get them to fix your L2TP login.

Once the connection is up, you should see the virtual PPP interface configured with the static IP that is assigned to it in clueless.

If you get stuck, pop into the IRC channel and see if I'm around (basil_uk) and I'll help if possible.

OpenWRT

I'll give details about doing things without LuCI - if you want to do it through the web UI, it should be obvious from the text config what you need to twiddle.

Tested with the following package versions -

kmod-l2tp - 3.18.10-1
kmod-l2tp-eth - 3.18.10-1
kmod-l2tp-ip - 3.18.10-1
kmod-pppol2tp - 3.18.10-1
ppp-mod-pppol2tp - 2.4.7-5
xl2tpd - 1.3.6-5619e1771048e74b729804e8602f409af0f3faea
luci-proto-ipv6 - git-15.090.50849-576e235-1
luci-proto-ppp - git-15.090.50849-576e235-1

You'll first need to create a static route for l2tp.aa.net.uk via your bulk interface (usually wan) in /etc/config/network -

config route
        option interface 'wan'
        option target '90.155.53.19'

Then add the tunnel to /etc/config/network - note that even though we enable it, the interface won't get an IPv6 address. Fear not, we can fix that in a minute.

config interface 'aaisp'
        option proto 'l2tp'
        option server 'l2tp.aa.net.uk'
        option username 'yourusername@a'
        option password 'YOURPASSWORD'
        option ipv6 '1'
        option peerdns '0'
        option metric '50'

Next let's configure DHCPv6 over the tunnel interface since PPP IPV6CP doesn't seem to work properly. Again in /etc/config/network - edit to taste if you don't want to gobble up your entire /48. Though this shows as a separate interface in OpenWRT-land, they'll both assign addresses to the same underlying interface, 'l2tp-aaisp'.

config interface 'aaisp6'
        option proto 'dhcpv6'
        option reqprefix '48'
        option peerdns '0'
        option _orig_ifname 'aaisp'
        option _orig_bridge 'false'
        option ifname 'l2tp-aaisp'
        option reqaddress 'force'

Now we have -

  • All IPv4 traffic going out of our bulk WAN interface (metric 0)
  • The L2TP tunnel has its default gateway set, but unused (metric 50)
  • All IPv6 traffic going out of the tunnel (haven't tested what would happen if your bulk interface was also IPv6 capable)
  • DNS unchanged from original setup (I use dnscrypt-proxy and some REDIRECT iptables plumbing to secure DNS query traffic)

Next steps

  • iptables PREROUTING rules to mark traffic that should egress via the tunnel
  • iproute2 magic to route the marked traffic properly
  • a painful sense of irony that we're dodging nasty shaping and filtering on our bulk interface only to do it ourselves
  • a really sweet hat

Prod me (daveio) on IRC if you have trouble, I'll try to assist if I'm around.

Linux / xl2tpd

  1. Ensure the following kernel options are set or the corresponding modules are available:
    1. CONFIG_PPPOL2TP
    2. CONFIG_L2TP
  2. Install xl2tpd and pppd on your Linux router.
  3. Edit /etc/xl2tpd/xl2tpd.conf to contain the following:
    [lac aaisp]
    lns = l2tp.aaisp.net.uk
    require authentication = no
    pppoptfile = /etc/ppp/options.aaisp
  4. Create /etc/ppp/options.aaisp containing the following (obviously change the name and password to match your L2TP login details):
    +ipv6
    ipv6cp-use-ipaddr
    name xyz@a.X
    password Your_xyz@A.X_password
    noauth
  5. Create the xl2tpd control file:
    mkdir -p /var/run/xl2tpd
    touch /var/run/xl2tpd/l2tp-control
  6. Start the xl2tpd service (for systemd, use service command for older RC systems):
    systemctl start xl2tpd
  7. Tell the daemon to connect to aaisp:
    echo "c aaisp" > /var/run/xl2tpd/l2tp-control

This should give you a new PPP device which encapsulates the L2TP connection.

Other Hardware

The TL-WR741ND router works, although it can only do NAT, but is very cheap.