Back up to the A&A Routers Page

Difference between revisions of "Category:Technicolor DGA4134"

From AAISP Support Site
Jump to navigation Jump to search
[quality revision][quality revision]
m
Line 30: Line 30:
 
*ADSL1, ADSL2+
 
*ADSL1, ADSL2+
 
*VDSL (FTTC)
 
*VDSL (FTTC)
*''G.Fast'' - using the red Ethernet WAN port connected '''to an existing G.FAST modem'''
+
*''G.Fast'' - connect the red Ethernet WAN port '''to an existing G.FAST modem'''
*''FTTP, FTTPoD'' - using the red Ethernet WAN port '''to the fibre termination 'modem''''
+
*''FTTP, FTTPoD'' - connect the red Ethernet WAN port '''to the fibre termination 'modem''''. Suitable for 1G/s FTTP, see note on speeds below.
   
 
'''Bridge mode:''' The automatic A&A configuration will not configure these routers as 'bridge'. If you want to use your own PPPoE router. In this case our basic ZyXEL is a better choice, or you can configure it manually: https://support.aa.net.uk/DGA0122_Bridge_Mode
 
'''Bridge mode:''' The automatic A&A configuration will not configure these routers as 'bridge'. If you want to use your own PPPoE router. In this case our basic ZyXEL is a better choice, or you can configure it manually: https://support.aa.net.uk/DGA0122_Bridge_Mode
  +
  +
  +
===Speeds===
  +
This router can be used with faster FTTP circuits, eg up to 1Gb/s. Throughput on wifi will be limited to much lower speeds, but devices connected using wired connections should see around 950 Mbps when using our speed tester.
   
 
==Admin and WiFi passwords==
 
==Admin and WiFi passwords==

Revision as of 19:40, 31 March 2022


DGA4134
Ports
Rear
Front

These pages are about the Technicolor DGA4134. .

Technicolor DGA4134

This router was introduced as a stop-gap for the DGA0122 in October 2021 due to supply shortages with the DGA0122.

The DGA4134 and the DGA0122 are very similar. They look physically different, but the user interface, and physical ports are very similar. The DGA4134 has WiFi 6 though. Some of the support pages for the DGA0122 are also relevant to the DGA4134.

Works well with the 'Technicolor OWA0131 WiFI Extender'.

Basic Specs

  • 4x 10/100M/1G LAN ports
  • 1x 1 GE WAN port
  • Modem supports VDSL (FTTC) and ADSL/ADSL2+ (Not G.Fast)
  • WiFi is:
    • 2.4GHz (2x2) Wi-Fi 6 (IEEE 802.11ax)
    • 5GHz (4x4) Wi-Fi 6 (IEEE 802.11ax)
  • 2 FXS ports, for connecting an analogue phone to a VoIP account

User information

Suitable for:

  • ADSL1, ADSL2+
  • VDSL (FTTC)
  • G.Fast - connect the red Ethernet WAN port to an existing G.FAST modem
  • FTTP, FTTPoD - connect the red Ethernet WAN port to the fibre termination 'modem'. Suitable for 1G/s FTTP, see note on speeds below.

Bridge mode: The automatic A&A configuration will not configure these routers as 'bridge'. If you want to use your own PPPoE router. In this case our basic ZyXEL is a better choice, or you can configure it manually: https://support.aa.net.uk/DGA0122_Bridge_Mode


Speeds

This router can be used with faster FTTP circuits, eg up to 1Gb/s. Throughput on wifi will be limited to much lower speeds, but devices connected using wired connections should see around 950 Mbps when using our speed tester.

Admin and WiFi passwords

We ship the router with a basic configuration which is just enough to get the router to log in to us and fetch its full configuration for your line. There are settings on the control pane which can set the SSID, passwords etc, but until the router has been sent its full configuration it is in an 'unconfigured' state.

As shipped / unconfigured Once configured
IP: 192.168.1.1 192.168.1.1 or your public block
Username: admin (or engineer for some superpowers)
Password: as stated on the rear panel as printed on the A&A card
Wifi Name:
WiFi Password:

Bugs & workarounds

Sadly, CPE has always had some quirks or bugs. We've identified a couple of problems with the DGA4134 and have listed them here:

Pages in category "Technicolor DGA4134"

The following 8 pages are in this category, out of 8 total.

Media in category "Technicolor DGA4134"

This category contains only the following file.