Back up to the Bonding Page

Difference between revisions of "FireBrick Bonding more than 3 lines"

From AAISP Support Site
Jump to: navigation, search
[unchecked revision][quality revision]
m (clean up, typos fixed: eg. → e.g. (2), a interface → an interface)
m (Overview)
 
(11 intermediate revisions by 4 users not shown)
Line 1: Line 1:
[[File:2700-small.png|link=:Category:FireBrick]]
+
<indicator name="Front">[[File:Menu-bonding.svg|link=:Category:Bonding|30px|Back up to the Bonding Page]]</indicator>
   
 
=Overview=
 
=Overview=
The FireBrick 2500/2700 has 4 ethernet ports, typically one port will be for the LAN connection (for example - to the main office switch), and the rest for connections to the ADSL/FTTC modems.
+
The FireBrick 2500/2700 have 4 ethernet ports, the 2900 has 4 plus an SFP which can be used with a Copper of fibre SFP to give an additional port. Typically one port will be for the LAN connection (for example - to the main office switch), and the rest for connections to the ADSL/FTTC modems.
   
 
As there are 4 ports are we restricted to only bonding up to 3 ADSL/FTTC lines? No.
 
As there are 4 ports are we restricted to only bonding up to 3 ADSL/FTTC lines? No.
Line 17: Line 17:
   
 
The switch would be set up for 4 (or more) separate VLANs on the appropriate ports, and on the FireBrick, the <ppp .../> config would have VLAN="n".
 
The switch would be set up for 4 (or more) separate VLANs on the appropriate ports, and on the FireBrick, the <ppp .../> config would have VLAN="n".
 
   
 
=VLAN Switch Config=
 
=VLAN Switch Config=
  +
Instructions on using a ZyXEL GS1900-8 switch: [[ZyXEL GS1900-8]]
Here are some notes on setting up a HP ProCurve 1810G-8:
 
  +
  +
Below are some notes on setting up a HP ProCurve 1810G-8:
   
 
The HP ProCurve 1810G-8 (J9449A) is a nice little 8 port managed switch. No fans and similar in size to a FireBrick.
 
The HP ProCurve 1810G-8 (J9449A) is a nice little 8 port managed switch. No fans and similar in size to a FireBrick.
Line 29: Line 30:
   
 
*Default IP is "192.168.2.10"
 
*Default IP is "192.168.2.10"
*Default Password is blank
+
*Default username: admin
  +
*Default password: 1234
   
 
==Save Config==
 
==Save Config==
Line 70: Line 72:
   
 
[[File:1810G-8-VLAN1.png|border|500px]]
 
[[File:1810G-8-VLAN1.png|border|500px]]
  +
  +
On some switches you may need to set the PVID accordingly - ie Port 1 = PVID 101, Port 2 = PVID 102 etc... This was needed on a PoE variant of a switch, but not on the non-PoE variant.
   
 
*SAVE CONFIG - otherwise you will learn the hard way
 
*SAVE CONFIG - otherwise you will learn the hard way
Line 78: Line 82:
 
Set the gateway to the FireBrick, then the switch can access things like time server, syslog server etc...
 
Set the gateway to the FireBrick, then the switch can access things like time server, syslog server etc...
   
  +
[[Category:Bonding]]
 
[[Category:FireBrick]]
+
[[Category:FireBrick|Bonding]]
  +
[[Category:Bonding Configuration]]

Latest revision as of 09:31, 22 May 2020


Overview

The FireBrick 2500/2700 have 4 ethernet ports, the 2900 has 4 plus an SFP which can be used with a Copper of fibre SFP to give an additional port. Typically one port will be for the LAN connection (for example - to the main office switch), and the rest for connections to the ADSL/FTTC modems.

As there are 4 ports are we restricted to only bonding up to 3 ADSL/FTTC lines? No.


To overcome the physical port restriction a VLAN switch can be used - for example:

ADSL MODEM 1  --                                           
ADSL MODEM 2  --                                           
ADSL MODEM 3  --  VLAN Switch  --  Firebrick  --  LAN SWITCH  ==  Computers
ADSL MODEM 4  --

The switch would be set up for 4 (or more) separate VLANs on the appropriate ports, and on the FireBrick, the <ppp .../> config would have VLAN="n".

VLAN Switch Config

Instructions on using a ZyXEL GS1900-8 switch: ZyXEL GS1900-8

Below are some notes on setting up a HP ProCurve 1810G-8:

The HP ProCurve 1810G-8 (J9449A) is a nice little 8 port managed switch. No fans and similar in size to a FireBrick.

Overview

The FireBrick will have a single WAN port, which will plug in to the HP Switch. The ADSL/FTTC modems will plug in to the HP Switch too. This will then, with VLANs, enable the FireBrick to use up to 7 ADSL/FTTC modems.

  • Default IP is "192.168.2.10"
  • Default username: admin
  • Default password: 1234

Save Config

To make things a little easier, here is a saved config: File:FBVLANconfig1810G.bin.zip. It is the default config (default IP and password), but with VLANs as follows:

  • Port 1 - VLAN 101, for ADSL line 1
  • Port 2 - VLAN 102, for ADSL line 2
  • Port 3 - VLAN 103, for ADSL line 3
  • Port 4 - VLAN 104, for ADSL line 4
  • Port 8 is for the FireBrick

The config was from HP ProCurve 1810G - 8 GE, P.1.17, eCos-2.0, Software Version, P.1.17

However it only takes a few minutes to set up the VLANs manually as follows:

Basic Settings

  • Set your computer to an IP in the same subnet as the switch, e.g. 192.168.2.11
  • Plug computer in to a port, e.g. port 7
  • Log in to http://192.168.2.10 with a blank password
  • Maybe set the system description details
  • Set admin password (Maintenance - Password Manager) then save and re-login
  • Enable HTTPS (Security - Secure Connection) generate certificate and apply

Create VLANs

We will set ports 1-4 to be VLANs 101, 102, 103, 104. We'll use port 8 for plugging in to the FireBrick, and use port 7 for our admin.

  • Create 4 VLANs (VLANS - VLAN Configuration)
  • Set the names to be ADSL1, ADSL2, ADSL3, ADSL4 - this will match the login/line numbers of the ADSL/FTTC lines

1810G-8-VLANSList.png

Configure ports for VLAN tagging

  • Under VLANs - Participation Tagging:
    • set VLAN 101 to be U on port 1 and T on port 8. E on rest
    • set VLAN 102 to be U on port 2 and T on port 8. E on rest
    • set VLAN 103 to be U on port 3 and T on port 8. E on rest
    • set VLAN 104 to be U on port 4 and T on port 8. E on rest
    • set VLAN 1 to be E on port 1, 2, 3, 4 and U on port 5, 6, 7, 8

1810G-8-VLAN101.png

1810G-8-VLAN1.png

On some switches you may need to set the PVID accordingly - ie Port 1 = PVID 101, Port 2 = PVID 102 etc... This was needed on a PoE variant of a switch, but not on the non-PoE variant.

  • SAVE CONFIG - otherwise you will learn the hard way

IP Address

In order to access the Switch, we'll need to setup an interface on the FireBrick with a subnet in the same range as the switch. We can use the default 192.168.2.0/24, and this will be accessible from the LAN side. Alternately, we can use a public /30. This will involve a new /30 allocation on Clueless, routed to all the ADSL/FTTC lines, and on the FireBrick a subnet on the WAN interface. Set the gateway to the FireBrick, then the switch can access things like time server, syslog server etc...