Difference between revisions of "IPv6 Configuration"

From AAISP Support Site
Jump to: navigation, search
[unchecked revision][quality revision]
(clean up)
 
(28 intermediate revisions by 10 users not shown)
Line 1: Line 1:
  +
= Related Pages on the A&A Website =
== IPv6 over IP Tunnelled Connections ==
 
* [[Cisco IPv6 Tunnel Config]]
 
* [[FreeBSD IPv6 Tunnel Config]]
 
   
  +
*[http://www.aaisp.net.uk/kb-broadband-ipv6.html www.aaisp.net.uk/kb-broadband-ipv6.html]
[[Category:IPv6]] [[Category::Configuring]]
 
  +
  +
== Useful Blog/HOWTO Entries ==
  +
  +
*[http://www.pitt-pladdy.com/blog/_20100123-184109%2B0000%20OpenWrt%20with%20native%20IPv6%20on%20DG834%20v2%20%28using%20AAISP%29/ Using OpenWRT as an IPv6 router]
  +
*[http://wiki.openwrt.org/doc/howto/ipv6 Configuring OpenWRT for IPv6]
  +
*[http://www.davidc.net/networking/ipv6-source-address-selection-linux IPv6 Source Address Selection on Linux]
  +
*[http://ipv6.raphnet.net/ Linux/BSD Configuration commands]
  +
  +
== IPv6 ready hardware ==
  +
  +
The following equipment has been successfully used as an IPv6 Router for home use. These are known as CPE or Customer Premises Equipment.
  +
  +
*Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem
  +
*Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem [[IPv6 SpeedTouch|Guide]]
  +
*Netgear DG834v2 running OpenWRT 8.09 (Kamikaze)
  +
*Linksys WRTU54G-TM running OpenWRT trunk build with a Netgear DM111P Modem
  +
*Netgear WNR854T running OpenWRT 10.03 (Backfire) with BT Openreach modem on FTTC
  +
*[[Router - Cisco IPv6 IOS Versions|Cisco Devices]] running 12.4 and above
  +
*Our [[FireBrick 2700]] page has info on Native IPv6 config (also applies to 2500)
  +
*[[Vigor 120]] - earlier firmware versions have problems with IPv6
  +
*Billion BiPAC 7800N with firmware 1.06d
  +
*The MikroTik [[RouterOS]] page has information on IPv6 configuration
  +
The search for additional IPv6 CPE possibilities: [[IPv6CPESearch]]
  +
* [[Router - Juniper SRX|Juniper SRX]] series of routers
  +
  +
== Native IPv6 Connections ==
  +
  +
*[[Cisco IPv6 Native Config]]
  +
*[[IPv6]] - How AAISP manage IPv6 on Broadband lines.
  +
  +
== IPv6 over IP Tunnelled Connections ==
  +
  +
*[[Cisco IPv6 Tunnel Config]]
  +
*[[FreeBSD IPv6 Tunnel Config]]
  +
*[[FireBrick 2700 v6 Tunnel]]
  +
*[[Debian IPv6 Tunnel Config]]
  +
*[[Linux NetworkManager IPv6 Tunnel Config]]
  +
  +
See also the configuration examples on the IPv6 Knowledge-base page referenced above.
  +
  +
[[Category:IPv6]] [[Category:Configuring]]
  +
  +
== FireBrick 2500/2700 ==
  +
  +
It's quite easy.... Assuming you have an IPv6 block allocated to your line on Clueless and you're using the FB for PPPoE, then all the FB config needs is:
  +
  +
*An IPv6 address on the LAN subnet
  +
*ra="true" in the subnet

Latest revision as of 00:00, 18 August 2018

Related Pages on the A&A Website

Useful Blog/HOWTO Entries

IPv6 ready hardware

The following equipment has been successfully used as an IPv6 Router for home use. These are known as CPE or Customer Premises Equipment.

  • Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem
  • Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem Guide
  • Netgear DG834v2 running OpenWRT 8.09 (Kamikaze)
  • Linksys WRTU54G-TM running OpenWRT trunk build with a Netgear DM111P Modem
  • Netgear WNR854T running OpenWRT 10.03 (Backfire) with BT Openreach modem on FTTC
  • Cisco Devices running 12.4 and above
  • Our FireBrick 2700 page has info on Native IPv6 config (also applies to 2500)
  • Vigor 120 - earlier firmware versions have problems with IPv6
  • Billion BiPAC 7800N with firmware 1.06d
  • The MikroTik RouterOS page has information on IPv6 configuration

The search for additional IPv6 CPE possibilities: IPv6CPESearch

Native IPv6 Connections

IPv6 over IP Tunnelled Connections

See also the configuration examples on the IPv6 Knowledge-base page referenced above.

FireBrick 2500/2700

It's quite easy.... Assuming you have an IPv6 block allocated to your line on Clueless and you're using the FB for PPPoE, then all the FB config needs is:

  • An IPv6 address on the LAN subnet
  • ra="true" in the subnet