IPv6 Configuration: Difference between revisions

From AAISP Support Site
(clean up)
(20 intermediate revisions by 9 users not shown)
Line 1: Line 1:
= Related Pages on the A&A Website: =
= Related Pages on the A&A Website =


*[http://www.aaisp.net.uk/kb-broadband-ipv6.html www.aaisp.net.uk/kb-broadband-ipv6.html]
*[http://www.aaisp.net.uk/kb-broadband-ipv6.html www.aaisp.net.uk/kb-broadband-ipv6.html]
Line 7: Line 7:
*[http://www.pitt-pladdy.com/blog/_20100123-184109%2B0000%20OpenWrt%20with%20native%20IPv6%20on%20DG834%20v2%20%28using%20AAISP%29/ Using OpenWRT as an IPv6 router]
*[http://www.pitt-pladdy.com/blog/_20100123-184109%2B0000%20OpenWrt%20with%20native%20IPv6%20on%20DG834%20v2%20%28using%20AAISP%29/ Using OpenWRT as an IPv6 router]
*[http://wiki.openwrt.org/doc/howto/ipv6 Configuring OpenWRT for IPv6]
*[http://wiki.openwrt.org/doc/howto/ipv6 Configuring OpenWRT for IPv6]
*[http://www.davidc.net/networking/ipv6-source-address-selection-linux IPv6 Source Address Selection on Linux]
*[http://ipv6.raphnet.net/ Linux/BSD Configuration commands]


== Consumer CPE Equipment ==
== IPv6 ready hardware ==


The following equipment has been successfully used as an IPv6 Router for home use
The following equipment has been successfully used as an IPv6 Router for home use. These are known as CPE or Customer Premises Equipment.


*Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem
*Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem
*Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem [[IPv6 SpeedTouch|Guide]]
*Netgear DG834v2 running OpenWRT 8.09 (Kamikaze)
*Netgear DG834v2 running OpenWRT 8.09 (Kamikaze)
*Linksys WRTU54G-TM running OpenWRT trunk build with a Netgear DM111P Modem
*Our [[FireBrick 2700]] page has info on Native IPv6 config
*Netgear WNR854T running OpenWRT 10.03 (Backfire) with BT Openreach modem on FTTC
*[[Router - Cisco IPv6 IOS Versions|Cisco Devices]] running 12.4 and above
*Our [[FireBrick 2700]] page has info on Native IPv6 config (also applies to 2500)
*[[Vigor 120]] - earlier firmware versions have problems with IPv6
*Billion BiPAC 7800N with firmware 1.06d
*The MikroTik [[RouterOS]] page has information on IPv6 configuration
The search for additional IPv6 CPE possibilities: [[IPv6CPESearch]]
* [[Router - Juniper SRX|Juniper SRX]] series of routers

== Native IPv6 Connections ==

*[[Cisco IPv6 Native Config]]
*[[IPv6]] - How AAISP manage IPv6 on Broadband lines.


== IPv6 over IP Tunnelled Connections ==
== IPv6 over IP Tunnelled Connections ==
Line 21: Line 37:
*[[FreeBSD IPv6 Tunnel Config]]
*[[FreeBSD IPv6 Tunnel Config]]
*[[FireBrick 2700 v6 Tunnel]]
*[[FireBrick 2700 v6 Tunnel]]
*[[Debian IPv6 Tunnel Config]]
*[[Linux NetworkManager IPv6 Tunnel Config]]


See also the configuration examples on the IPv6 Knowledge-base page referenced above.
See also the configuration examples on the IPv6 Knowledge-base page referenced above.

Revision as of 00:00, 18 August 2018

Related Pages on the A&A Website

Useful Blog/HOWTO Entries

IPv6 ready hardware

The following equipment has been successfully used as an IPv6 Router for home use. These are known as CPE or Customer Premises Equipment.

  • Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem
  • Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem Guide
  • Netgear DG834v2 running OpenWRT 8.09 (Kamikaze)
  • Linksys WRTU54G-TM running OpenWRT trunk build with a Netgear DM111P Modem
  • Netgear WNR854T running OpenWRT 10.03 (Backfire) with BT Openreach modem on FTTC
  • Cisco Devices running 12.4 and above
  • Our FireBrick 2700 page has info on Native IPv6 config (also applies to 2500)
  • Vigor 120 - earlier firmware versions have problems with IPv6
  • Billion BiPAC 7800N with firmware 1.06d
  • The MikroTik RouterOS page has information on IPv6 configuration

The search for additional IPv6 CPE possibilities: IPv6CPESearch

Native IPv6 Connections

IPv6 over IP Tunnelled Connections

See also the configuration examples on the IPv6 Knowledge-base page referenced above.

FireBrick 2500/2700

It's quite easy.... Assuming you have an IPv6 block allocated to your line on Clueless and you're using the FB for PPPoE, then all the FB config needs is:

  • An IPv6 address on the LAN subnet
  • ra="true" in the subnet