Difference between revisions of "IPv6 Configuration"

From AAISP Support Site
Jump to: navigation, search
[unchecked revision][quality revision]
(IPv6 over IP Tunnelled Connections)
(clean up)
 
(12 intermediate revisions by 7 users not shown)
Line 1: Line 1:
= Related Pages on the A&A Website: =
+
= Related Pages on the A&A Website =
   
 
*[http://www.aaisp.net.uk/kb-broadband-ipv6.html www.aaisp.net.uk/kb-broadband-ipv6.html]
 
*[http://www.aaisp.net.uk/kb-broadband-ipv6.html www.aaisp.net.uk/kb-broadband-ipv6.html]
Line 15: Line 15:
   
 
*Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem
 
*Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem
*Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem [[IPv6_SpeedTouch|Guide]]
+
*Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem [[IPv6 SpeedTouch|Guide]]
 
*Netgear DG834v2 running OpenWRT 8.09 (Kamikaze)
 
*Netgear DG834v2 running OpenWRT 8.09 (Kamikaze)
  +
*Linksys WRTU54G-TM running OpenWRT trunk build with a Netgear DM111P Modem
  +
*Netgear WNR854T running OpenWRT 10.03 (Backfire) with BT Openreach modem on FTTC
  +
*[[Router - Cisco IPv6 IOS Versions|Cisco Devices]] running 12.4 and above
 
*Our [[FireBrick 2700]] page has info on Native IPv6 config (also applies to 2500)
 
*Our [[FireBrick 2700]] page has info on Native IPv6 config (also applies to 2500)
  +
*[[Vigor 120]] - earlier firmware versions have problems with IPv6
 
  +
*Billion BiPAC 7800N with firmware 1.06d
  +
*The MikroTik [[RouterOS]] page has information on IPv6 configuration
 
The search for additional IPv6 CPE possibilities: [[IPv6CPESearch]]
 
The search for additional IPv6 CPE possibilities: [[IPv6CPESearch]]
  +
* [[Router - Juniper SRX|Juniper SRX]] series of routers
   
== IPv6 over IP Tunnelled Connections ==
+
== Native IPv6 Connections ==
   
 
*[[Cisco IPv6 Native Config]]
 
*[[Cisco IPv6 Native Config]]
  +
*[[IPv6]] - How AAISP manage IPv6 on Broadband lines.
  +
  +
== IPv6 over IP Tunnelled Connections ==
  +
 
*[[Cisco IPv6 Tunnel Config]]
 
*[[Cisco IPv6 Tunnel Config]]
 
*[[FreeBSD IPv6 Tunnel Config]]
 
*[[FreeBSD IPv6 Tunnel Config]]
 
*[[FireBrick 2700 v6 Tunnel]]
 
*[[FireBrick 2700 v6 Tunnel]]
  +
*[[Debian IPv6 Tunnel Config]]
  +
*[[Linux NetworkManager IPv6 Tunnel Config]]
   
 
See also the configuration examples on the IPv6 Knowledge-base page referenced above.
 
See also the configuration examples on the IPv6 Knowledge-base page referenced above.

Latest revision as of 00:00, 18 August 2018

Related Pages on the A&A Website

Useful Blog/HOWTO Entries

IPv6 ready hardware

The following equipment has been successfully used as an IPv6 Router for home use. These are known as CPE or Customer Premises Equipment.

  • Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem
  • Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem Guide
  • Netgear DG834v2 running OpenWRT 8.09 (Kamikaze)
  • Linksys WRTU54G-TM running OpenWRT trunk build with a Netgear DM111P Modem
  • Netgear WNR854T running OpenWRT 10.03 (Backfire) with BT Openreach modem on FTTC
  • Cisco Devices running 12.4 and above
  • Our FireBrick 2700 page has info on Native IPv6 config (also applies to 2500)
  • Vigor 120 - earlier firmware versions have problems with IPv6
  • Billion BiPAC 7800N with firmware 1.06d
  • The MikroTik RouterOS page has information on IPv6 configuration

The search for additional IPv6 CPE possibilities: IPv6CPESearch

Native IPv6 Connections

IPv6 over IP Tunnelled Connections

See also the configuration examples on the IPv6 Knowledge-base page referenced above.

FireBrick 2500/2700

It's quite easy.... Assuming you have an IPv6 block allocated to your line on Clueless and you're using the FB for PPPoE, then all the FB config needs is:

  • An IPv6 address on the LAN subnet
  • ra="true" in the subnet