L2TP Starlink: Difference between revisions

Back up to the Incoming L2TP Category
From AAISP Support Site
mNo edit summary
mNo edit summary
Line 2: Line 2:
[[Category:Incoming L2TP]]
[[Category:Incoming L2TP]]


== Using the AAISP L2TP service to get public IPv4 and public IPv6 addresses over a Starlink connection ==
= Using the AAISP L2TP service to get public IPv4 and public IPv6 addresses over a Starlink connection ==


=== Overview: ===
== Overview: ==


'''The L2TP service''' from AAISP can will route a small block of public IPv4 address and IPv6 addresses to your (L2TP compatible) router. This gives you the ability to use pubic IP addresses that are not filtered, not behind Carrier Grade NAT or any sort of NAT. All you need us a router capable of L2TP and an [https://www.aa.net.uk/broadband/l2tp-service/ L2TP service from AAISP].
'''The L2TP service''' from AAISP can will route a small block of public IPv4 address and IPv6 addresses to your (L2TP compatible) router. This gives you the ability to use pubic IP addresses that are not filtered, not behind Carrier Grade NAT or any sort of NAT. All you need us a router capable of L2TP and an [https://www.aa.net.uk/broadband/l2tp-service/ L2TP service from AAISP].
Line 10: Line 10:
'''Starlink''' is a satellite-based internet service and is initially provided without IPv6 and uses CGNAT for IPv4.
'''Starlink''' is a satellite-based internet service and is initially provided without IPv6 and uses CGNAT for IPv4.


=== In use: ===
== In use: ==




We have customers using our L2TP service over their Starlink, and the initial reports are that:
We have customers using our L2TP service over their Starlink, and the initial reports are that:
Line 20: Line 22:


Our L2TP service enables the Starlink customer to have static, public, IPv4 and IPv6 addresses.
Our L2TP service enables the Starlink customer to have static, public, IPv4 and IPv6 addresses.
┌──────────┐ ┌────────┐
┌───────────┐ ┌─────────┐ ┌─────────┐ │ │ │ │
│ Your LAN ├──────┤ Router ├───────┤Starlink ├─────────┤ Internet │ │ AAISP │
└───────────┘ └────┬────┘ └─────────┘ │ │ │ │
│ └──────────┘ └────┬───┘
│ │
└────────────────────────────────────────────────────────┘


Here is a graph from an L2TP service:
Here is a graph from an L2TP service:
Line 26: Line 35:


Note: This feedback based a very small number of connections (2 as of April 2021!), so the service may vary/improve depending on location and as Starlink add more satellites.
Note: This feedback based a very small number of connections (2 as of April 2021!), so the service may vary/improve depending on location and as Starlink add more satellites.

== How to use it ==

Starlink

Revision as of 08:54, 24 September 2021


Using the AAISP L2TP service to get public IPv4 and public IPv6 addresses over a Starlink connection =

Overview:

The L2TP service from AAISP can will route a small block of public IPv4 address and IPv6 addresses to your (L2TP compatible) router. This gives you the ability to use pubic IP addresses that are not filtered, not behind Carrier Grade NAT or any sort of NAT. All you need us a router capable of L2TP and an L2TP service from AAISP.

Starlink is a satellite-based internet service and is initially provided without IPv6 and uses CGNAT for IPv4.

In use:

We have customers using our L2TP service over their Starlink, and the initial reports are that:

  • Speed is good (especially compared to their slow DSL service)
  • Latency is OK - about 40-50ms, but there are some latency spikes (shown as green on the graph below)
  • Slight packetloss (shown as red on the graph below)
  • They enjoy the public IPv4 and IPv6 from us
  • Overall - worth it!

Our L2TP service enables the Starlink customer to have static, public, IPv4 and IPv6 addresses.

                                                         ┌──────────┐       ┌────────┐
┌───────────┐      ┌─────────┐       ┌─────────┐         │          │       │        │
│ Your LAN  ├──────┤ Router  ├───────┤Starlink ├─────────┤ Internet │       │ AAISP  │
└───────────┘      └────┬────┘       └─────────┘         │          │       │        │
                        │                                └──────────┘       └────┬───┘
                        │                                                        │
                        └────────────────────────────────────────────────────────┘

Here is a graph from an L2TP service:

L2TP over Starlink - showing slight packet loss and some latency spikes

Note: This feedback based a very small number of connections (2 as of April 2021!), so the service may vary/improve depending on location and as Starlink add more satellites.

How to use it

Starlink