VMG1312-B10A: Factory Reset
There are 4 configuration settings that the router can be in:
|State||Info||How to apply|
|ZyXEL Factory Settings||The actual state of the router before AAISP apply their 'base' setting||'save_default clean' command via CLI. More info below|
|AAISP Base Settings||As supplied by AAISP before the config for your line is applied, the settings allow the router to get online and obtain the specific configuration for your line||Upload AAISP's rom-d file. Not usually required as it is usually already loaded by AAISP, More info below.|
|Configured by AAISP||The settings for your specific line, along with settings as per the Control Pages||Usually when first plugged in on a customer line. Or, Via the Control Pages, or by holding in reset for 5 sec. More info below|
|Customer Edited||If customer makes further changes to their config after AAISP has sent the settings||Restore from a backup you made previously|
When supplied by AAISP, the router will be in the 'AAISP Base Settings' state. This is a temporary state and the router will receive its line-specific configuration when it first logs in.
Holding in the reset button will revert the configuration back to the AAISP Base Settings. Further work is needed to revert the config back to the ZyXEL factory settings. See below.
Reset to AAISP Base Settings
To reset the router to the AAISP base settings, follow these steps:
- Switch router on, wait for it to boot up
- With a paperclip, pen, etc., hold in the reset button
- Wait until power flashes red, keep holding it down until power stops flashing.
- Release the reset button
- Wait for the router to boot up again
About the AAISP Base settings
The reset state is the state the router was in when we sent it to you. In most cases that will mean is has been given our 'standard' configuration. This configuration has settings for it to talk back to AAISP and request its own configuration for the line that it's connected to.
When a router is in AAISP Base Settings it will connect to AAISP using a temporary 'provisioning' login. This default configuration will connect either by the DSL port or the WAN 4 port. When it connects the router will be sent a software upgrade if there is one available, and then will be sent its individual configuration for the connection.
- For more information about the AAISP configuration see: VMG1312-AAISP Configuration
A factory reset router will also be send an updated firmware if there is one available.
Reset to the ZyXEL Factory Settings
To erase the default AAISP settings, the 'ROM-D' file needs to be cleared, this is done via the CLI (Telnet or SSH) using the supervisor user and then issuing the
save_default clean command.
Here is an example:
$ telnet 220.127.116.11 Trying 18.104.22.168... Connected to brick.h.hearn.org.uk. Escape character is '^]'. VMG1312-B10A Login: supervisor Password: [your admin password] > save_default clean ROM-D cleaned.
At this point you can reset the router for this to be applied. The router will then boot up in its original factory settings without any of the AAISP configuration settings. You can reset the router by holding in the reset button for 5 seconds.
In this state, the router has ZyXEL's default IP address, username and password.
Adding the AAISP rom-d file
If you need to restore an AAISP rom-d file, then here are the steps to take. Support are able to provide you with the rom-d file on request.
FTP is used to add the rom-d file. Here the AAISP provided rom-d file is actually called vmg1312-b.rom-d, so when we upload it we have to specify the target file name of rom-d. (the lines highlighted contain things you need to type in)
$ ftp email@example.com Connected to 192.168.0.1. 220 Ftp firmware update utility 331 Password please. Password: zyad1234 230 User logged in. Remote system type is UNIX. Using binary mode to transfer files. ftp> put vmg1312-b.rom-d rom-d local: vmg1312-b.rom-d remote: rom-d 229 Entering extended passive mode (|||47630|) 150 BINARY data connection established. 100% |*************************************************************************| 72063 101.21 MiB/s 00:00 ETA 226 Ftp image done. PLEASE TYPE 'bye' or 'quit' NOW to quit ftp and the Router will start writing the image to flash. 72063 bytes sent in 00:02 (28.38 KiB/s) ftp> quit 221 The Router is rebooting...
At this point the ftp connection is closed and as it says, the router will reboot. The router will still need to be reset before the router will use the rom-d settings. Once reset though, the router will use the AAISP Base Settings to get online, retrieve a new firmware if available and then retrieve a config file for the line.
If you get an error such as:
bftpd:error:341.231:cmsImg_validateImage:1514:Could not determine image format [72063 bytes]
Then this will be due to the Firmware version not matching the version that the config file was made for. See the Software Page for information about the software versions.