VoIP Firewall

From AAISP Support Site
Revision as of 14:15, 1 November 2018 by Adsb (talk | contribs) (Add an example for a consumer router (e.g. ZyXEL). Needs 6 rules - or 12 if your RTP port range doesn't include 5060)
The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.

Go to the VoIP Category

This is what we suggest firewall-wise for VoIP customers:

Avoid using NAT where possible. However, some NAT gateways provide an adequate SIP ALG (e.g. Technicolor TG582), and some devices provide NAT that works with the new call server (e.g. FireBrick FB2700 and many simple NAT routers). If NAT works, then well done, but if not we cannot guarantee to be able to make it work.

Firewall Requirements on the AAISP VoIP Platform
Target Ports Source IPs
SIP (IPv4) UDP 5060 81.187.30.110 - 81.187.30.119

90.155.3.0/24 90.155.103.0/24

SIP (IPv6) UDP 5060 2001:8b0:0:30::5060:0/112

2001:8b0:5060::/48

RTP (IPv4) UDP 1024-65535 81.187.30.110 - 81.187.30.119

90.155.3.0/24 90.155.103.0/24

RTP (IPv6) UDP 1024-65535 2001:8b0:0:30::5060:0/112

2001:8b0:5060::/48

Customers should add all IPs above to their firewall rules even if you don't see traffic from or to them.

SIP is the call routing information that creates and manages calls. In practice if you allow port 5060 from the outside world you'll see attacks and possibly receive spam phone calls. We do not recommend leaving 5060 open unless you really know what you are doing. Phones rarely use ports as low as 5060 for media.

RTP is the actual media (e.g., the audio). On our platform the RTP will come from the same call server IP address as the SIP control messages. On most phones you can configure which ports to use for RTP, so you can restrict this range further. Note that RTP actually uses 2 consecutive port numbers, you should specify an even number and RTP will also use that port number +1. For example, on a Snom Phone the default range for RTP is 49152 to 65534, so the firewall needs to allow the port number range 49152 to 65535. As another example, Grandstream phones and ATAs tend to default to using 5004 as the RTP port, so you need to allow ports 5004-5005 through the firewall.

On routers which need one rule per IP address range you can halve the number of firewall rules needed as long as the source IP address ranges for SIP and RTP are the same and that the RTP port range you specify includes 5060.

In CIDR notation, the IPv4 range 81.187.30.110 - 81.187.30.119 needs two blocks:

81.187.30.110/31
81.187.30.112/29

Example FireBrick Config

Allow inbound calls to your VoIP Phone, if you register it with FireBrick:

<rule name="Allow Firebrick" source-interface="self" comment="Allow all from the FireBrick to LAN"/>

Allow inbound calls to your VoIP Phone, if you register it with Voiceless:

<rule name="SIP" source-ip="81.187.30.110-119 90.155.3.0/24 90.155.103.0/24 2001:8b0:0:30::5060:0/112 2001:8b0:5060::/48" target-ip="1.2.3.4" target-port="5060" action="accept"/>
<rule name="RTP" source-ip="81.187.30.110-119 90.155.3.0/24 90.155.103.0/24 2001:8b0:0:30::5060:0/112 2001:8b0:5060::/48" target-ip="1.2.3.4" target-port="1024-65535" protocol="17" action="accept"/>

Allow inbound calls to your Snom Phone, if you register it with Voiceless:

<rule name="SIP" source-ip="81.187.30.110-119 90.155.3.0/24 90.155.103.0/24 2001:8b0:0:30::5060:0/112 2001:8b0:5060::/48" target-ip="1.2.3.4" target-port="5060" action="accept"/>
<rule name="RTP" source-ip="81.187.30.110-119 90.155.3.0/24 90.155.103.0/24 2001:8b0:0:30::5060:0/112 2001:8b0:5060::/48" target-ip="1.2.3.4" target-port="49152-65535" protocol="17" action="accept"/>

Example consumer router config

The following example is for an AAISP-supplied ZyXEL router. Because the Custom Destination Port range covers port 5060 we get away with half the rules!

Firewall Rules on the AAISP VoIP Platform
Filter name Source IP Address IP Type Protocol Custom Destination Port Policy Direction
VoIP6A 2001:8b0:0:30::5060:0/112 IPv6 UDP 5000-5999 ACCEPT WAN to LAN
VoIP6B 2001:8b0:5060::/48 IPv6 UDP 5000-5999 ACCEPT WAN to LAN
VoIP4A 81.187.30.110/31 IPv4 UDP 5000-5999 ACCEPT WAN to LAN
VoIP4B 81.187.30.112/29 IPv4 UDP 5000-5999 ACCEPT WAN to LAN
VoIP4C 90.155.3.0/24 IPv4 UDP 5000-5999 ACCEPT WAN to LAN
VoIP4D 90.155.103.0/24 IPv4 UDP 5000-5999 ACCEPT WAN to LAN

Other things to Firewall

  • Don't allow access to your phone or servers web configuration pages from the Internet.
  • If you run your own server and allow phones to use it from your WAN/Internet, then lock this down as much as possible - perhaps only allow access to your PBX from the Internet via a VPN.


NAT

Avoid using NAT where possible. However, some NAT gateways provide an adequate SIP ALG (e.g. Technicolor TG582), and some devices provide NAT that works with the new call server (e.g. FireBrick 2500/2700 and many simple NAT routers). If NAT works, then well done, but if not we cannot guarantee to be able to make it work. See: VoIP NAT


Further VoIP Security

  • Please see our VoIP Security page for further information on securing your phones, accounts and VoIP systems.