Jump to content

This is the support site for Andrews & Arnold Ltd, a UK Internet provider. Information on these pages is generally for our customers but may be useful to others, enjoy!

VoIP Phones - Asterisk: Difference between revisions

 
= Configuration =
Asterisk has two methods to configure SIP connections. The legacy "sip.conf" (SIP) and the more modern "pjsip.conf" (PJSIP).
 
Newer installations of Asterisk should be configured to use PJSIP as it will be more supported as Asterisk development continues. It isn't a good idea to have an installation that mixes sip.conf with pjsip.conf.
 
When reading the instructions below be aware which are for sip.conf and which are for pjsip.conf. PJSIP examples are below the SIP examples on this page.
== Incoming Calls ==
=== User Section ===
==Note: Order of sip.conf is important==
In sip.conf, ensure that your incoming config is before the config for the outgoing.
 
 
==PJSIP: Keep-Alive / Anti-Idle==
If you are using a firewall or NAT router with short timeouts on UDP sessions you can force packets to be sent over the connection to keep it alive.
 
Set qualify_frequency in the aor section; This triggers an OPTIONS message every X (as set) seconds.
An example of the aor section follows:
[aaisptrunk]
type = aor
contact = sip:+442082881111@voiceless.aa.net.uk
qualify_frequency=20
 
==Note: Asterisk and IPv6 SLAAC addresses==
Localnet should of course be set to whatever RFC1918 range you are using on your LAN.
 
=PJSIP=
 
==Dialplan==
</syntaxhighlight>
 
==PJSIP: Trunk registration==
Here is an example of a working pjsip.conf setup where Asterisk will register with A&A to receive calls.
 
In pjsip.conf:
[reg_442082881111]
type = registration
retry_interval = 20
fatal_retry_interval = 20
forbidden_retry_interval = 20
max_retries = 9999
auth_rejection_permanent = no
contact_user = maininbound
expiration = 120
outbound_auth = auth_reg_442082881111
client_uri = sip:+442082881111@voiceless.aa.net.uk
server_uri = sip:voiceless.aa.net.uk
[auth_reg_442082881111]
type = auth
password = BusinessPaidGrewCome
username = +442082881111
[aaisptrunk]
type = aor
contact = sip:+442082881111@voiceless.aa.net.uk
qualify_frequency=20
[aaisptrunk]
type = identify
endpoint = aaisptrunk
match = voiceless.aa.net.uk
[aaisptrunk]
type = endpoint
context = maininbound
dtmf_mode = rfc4733
disallow = all
allow = alaw
allow = ulaw
direct_media = no
aors = aaisptrunk
outbound_auth=auth_reg_442082881111
 
Calls come into the context "maininbound" in extensions.conf - in this example calls get sent onto extension 222 and 205 for 20 seconds and then go to voicemail.
[maininbound]
exten = maininbound,1,Dial(PJSIP/222&PJSIP/205,20)
exten = maininbound,n,Voicemail(222@default,us)
 
In extensions.conf you can dial out via the trunk with:
Dial(PJSIP/0800500005@aaisptrunk,,)
 
==PJSIP: Keep-Alive / Anti-Idle==
If you are using a firewall or NAT router with short timeouts on UDP sessions you can force packets to be sent over the connection to keep it alive.
 
Set qualify_frequency in the aor section; This triggers an OPTIONS message every X (as set) seconds.
An example of the aor section follows:
[aaisptrunk]
type = aor
contact = sip:+442082881111@voiceless.aa.net.uk
qualify_frequency=20
 
=Further Help=
autoreview, editor
93

edits