VoIP Phones - Gigaset N300: Difference between revisions
| Line 59: | Line 59: | ||
== Configuring the S685IP / A580IP / N300A == |
|||
If there are problems in setting up the S685IP it is easiest to start from a factory reset condition. This can be achieved by holding the blue button on the front of the base unit while power cycling it. After this the handset will need to be re-registered with the base unit (hold the blue button on the base unit while power cycling the handset). The pin should be changed from its default value of 0000 using the handset. |
If there are problems in setting up the S685IP it is easiest to start from a factory reset condition. This can be achieved by holding the blue button on the front of the base unit while power cycling it. After this the handset will need to be re-registered with the base unit (hold the blue button on the base unit while power cycling the handset). The pin should be changed from its default value of 0000 using the handset. |
||
| Line 83: | Line 81: | ||
If you're behind NAT, then you'll need Support to set your number to the old legacy 'Asterisk' server and use the server/proxy etc as a.speechless.aaisp.net.uk - Don't set the stun server though. |
If you're behind NAT, then you'll need Support to set your number to the old legacy 'Asterisk' server and use the server/proxy etc as a.speechless.aaisp.net.uk - Don't set the stun server though. |
||
= Registration with the old C Server = |
= Registration with the old C Server = |
||
Revision as of 15:45, 12 Haziran 2013
Configuring a Siemens Gigaset phone for AAISP
| Feature Notes | |
|---|---|
| Supports 302 Redirect | No |
| Tested on FireBrick SIP Server | Yes |
| IPv6 Support | No |
These notes are the same for configuring an S685IP, A580IP and N300A too.
N300 and Voiceless
On the web interface, go to:
Settings - Telephony - Edit 1, Show Advanced Settings
| Gigaset N300 Settings | |
|---|---|
| Setting | Value |
| Connection Name or Number | AAISP (Or whatever you like) |
| Authentication Name | Your Number |
| Authentication Password | Your Password |
| Username | Your Number |
| Domain | Can be left blank |
| Proxy Server Address | voiceless.aa.net.uk |
| Registration server | voiceless.aa.net.uk |
Then you'll need to assign this account to a handset for incoming calls, this is set under
Settings - Telephony - Number Assignment
Don't forget to secure the base station with a new PIN!
If there are problems in setting up the S685IP it is easiest to start from a factory reset condition. This can be achieved by holding the blue button on the front of the base unit while power cycling it. After this the handset will need to be re-registered with the base unit (hold the blue button on the base unit while power cycling the handset). The pin should be changed from its default value of 0000 using the handset.
Starting from a factory reset, the following items need to be set using the web server in the base unit.
IP address:
By default the base unit picks up an ip address using DHCP. This can be over-ridden by connecting to "Settings -> IP Configuration", selecting "Static" and filling in the address details as required. Then click on the "Set" button.
Audio settings:
In menu "Settings -> Telephony -> Audio" select "Voice Quality - Own Codec preference". For "IP1" remove all codecs except "G.711 a law". This setting will generally give the best audio quality.
Other settings:
If there are problems with recognition of dtmf tones by other systems consider setting "RFC2833" in the "Settings -> Telephony -> Advanced Settings" menu. Avoid using "Audio".
Check that the Number Plan is set to use the VoIP rather than the fixed (pstn) line.
If you're behind NAT, then you'll need Support to set your number to the old legacy 'Asterisk' server and use the server/proxy etc as a.speechless.aaisp.net.uk - Don't set the stun server though.
Registration with the old C Server
Select menu "Settings -> Telephony -> Connections" and click the "Edit" button for IP1. Then click the "Show Advanced Settings" button and fill in the following fields:
Authentication Name: <aaisp phone number> (this can be in either UK or international format, for example +44203095nnnn or 0203095nnnn )
Authentication password: <password> (This is the same password that is set on the AAISP control pages for this number. Some non-alphanumeric characters can cause registration failure. In particular avoid "#" and "/")
Username: <aaisp phone number>
Domain: proxy.aasip.co.uk (Don't accidentally type aaisp!)
Proxy server address: proxy.aasip.co.uk
Registrar server: registrar.aasip.co.uk
All the other fields can be left as they are unless you are using NAT in which case the "Stun enabled" button should be selected and the "Stun server" set to stun.aaisp.net
When everything is entered click on the "Set" button. The display will return to the "Settings -> Telephony -> Connections" menu. Check that "IP1" is active and that the status is "Registered". You may wish to disable "Gigaset.net" in this menu. It should now be possible to make and receive calls.
Also see VoIP Security