Router - TP-Link - TD-W9980: Difference between revisions
CrazyTeeka (talk | contribs) mNo edit summary |
m (clean up, typos fixed: ie, → i.e.,, 100Mbps → 100Mbit/s (3)) |
||
(17 intermediate revisions by 2 users not shown) | |||
Line 4: | Line 4: | ||
=Specs= |
=Specs= |
||
*VDSL2/ADSL2+ Modem Router, supporting up to |
*VDSL2/ADSL2+ Modem Router, supporting up to 100Mbit/s broadband speeds. |
||
*Simultaneous 2. |
*Simultaneous 2.4 GHz 300Mbit/s and 5 GHz 300Mbit/s WiFi. |
||
*4 Gigabit Ports. |
*4 Gigabit Ports. |
||
*Ethernet WAN (EWAN) for connecting to VDSL/ADSL modems. |
*Ethernet WAN (EWAN) for connecting to VDSL/ADSL modems. |
||
*WiFi On/Off Switch allows users to simply turn their wireless radio on or off. |
*WiFi On/Off Switch allows users to simply turn their wireless radio on or off. |
||
*Supports IPv6. |
*Supports IPv6. |
||
*Annex A/B/L/M. |
|||
*Bit Swap. |
|||
*SRA. |
|||
=Firmware= |
|||
Latest firmware is here: [http://uk.tp-link.com/support/download/?model=TD-W9980&version=V1 TP-Link TD-W9980 Firmware] |
|||
=Factory Reset= |
=Factory Reset= |
||
With the router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it. |
*Method 1: With the router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it. |
||
*Method 2: Login to router, click "System Tools", click "Factory Defaults", click "Restore", router will reboot with factory defaults. |
|||
=Default Username/Password= |
|||
{|class="wikitable" |
|||
!colspan="2"|Default Username/Password |
|||
|- |
|||
!IP: |
|||
|192.168.1.1 |
|||
|- |
|||
!Username: |
|||
|admin |
|||
|- |
|||
!Password: |
|||
|admin |
|||
|} |
|||
=Quick Start - ADSL Modem Router= |
|||
#Click "Quick Setup". |
|||
#Start - Click "Next". |
|||
#Region and Time Zone - Choose "United Kingdom" and "(GMT)", click "Next". |
|||
#Operation Mode - Choose "xDSL Modem Router Mode", click "Next". |
|||
#Select ISP - From ISP List choose "ADSL_BT", click "Next". |
|||
#PPPoA - Enter broadband username and password, click "Next". |
|||
#Wireless 2.4 GHz - Change WiFi SSID and Password (Optional), click "Next". |
|||
#Wireless 5 GHz - Change WiFi SSID and Password (Optional), click "Next". |
|||
#Confirm - Check settings then click "Save". |
|||
=Quick Start - VDSL Modem Router= |
|||
#Click "Quick Setup". |
|||
#Start - Click "Next". |
|||
#Region and Time Zone - Choose "United Kingdom" and "(GMT)", click "Next". |
|||
#Operation Mode - Choose "xDSL Modem Router Mode", click "Next". |
|||
#Select ISP - From ISP List choose "VDSL_AAISP", click "Next". |
|||
#PPPoE - Enter broadband username and password, click "Next". |
|||
#Wireless 2.4 GHz - Change WiFi SSID and Password (Optional), click "Next". |
|||
#Wireless 5 GHz - Change WiFi SSID and Password (Optional), click "Next". |
|||
#Confirm - Check settings then click "Save". |
|||
=Quick Start - PPPoE Router= |
|||
#Click "Quick Setup". |
|||
#Start - Click "Next". |
|||
#Region and Time Zone - Choose "United Kingdom" and "(GMT)", click "Next". |
|||
#Operation Mode - Choose "Wireless Router Mode", click "Next". |
|||
#Ethernet WAN Type - Choose "PPPoE", click "Next". |
|||
#PPPoE - Enter broadband username and password, click "Next". |
|||
#Wireless 2.4 GHz - Change WiFi SSID and Password (Optional), click "Next". |
|||
#Wireless 5 GHz - Change WiFi SSID and Password (Optional), click "Next". |
|||
#Confirm - Check settings then click "Save". |
|||
=Bridge - ADSL Modem= |
|||
#Click "Network". |
|||
#Click "WAN Settings". |
|||
#Click "Add". |
|||
#DSL Modulation Type: ADSL |
|||
#VPI: 0 |
|||
#VCI: 38 |
|||
#Connection Type: Bridge |
|||
#Click "Save". |
|||
=Bridge - VDSL Modem= |
|||
#Click "Network". |
|||
#Click "WAN Settings". |
|||
#Click "Add". |
|||
#DSL Modulation Type: VDSL |
|||
#Enable VLAN ID: ✓ |
|||
#VLAN ID: 101 |
|||
#Connection Type: Bridge |
|||
#Click "Save". |
|||
==Bridging Notes== |
|||
#Firmware TD-W9980_V1_150507 07/05/15 does not support *at least* 1508 byte frames so as to allow RFC4638 PPPoE to a connected device. i.e., 1500 byte MTU is not possible when in bridge mode. |
|||
#*AAISP contacted TP-Link regarding this 2015-09-12 |
|||
[[Category:3rd Party Routers|TP Link]] |
Latest revision as of 00:04, 15 March 2017
Specs
- VDSL2/ADSL2+ Modem Router, supporting up to 100Mbit/s broadband speeds.
- Simultaneous 2.4 GHz 300Mbit/s and 5 GHz 300Mbit/s WiFi.
- 4 Gigabit Ports.
- Ethernet WAN (EWAN) for connecting to VDSL/ADSL modems.
- WiFi On/Off Switch allows users to simply turn their wireless radio on or off.
- Supports IPv6.
- Annex A/B/L/M.
- Bit Swap.
- SRA.
Firmware
Latest firmware is here: TP-Link TD-W9980 Firmware
Factory Reset
- Method 1: With the router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it.
- Method 2: Login to router, click "System Tools", click "Factory Defaults", click "Restore", router will reboot with factory defaults.
Default Username/Password
Default Username/Password | |
---|---|
IP: | 192.168.1.1 |
Username: | admin |
Password: | admin |
Quick Start - ADSL Modem Router
- Click "Quick Setup".
- Start - Click "Next".
- Region and Time Zone - Choose "United Kingdom" and "(GMT)", click "Next".
- Operation Mode - Choose "xDSL Modem Router Mode", click "Next".
- Select ISP - From ISP List choose "ADSL_BT", click "Next".
- PPPoA - Enter broadband username and password, click "Next".
- Wireless 2.4 GHz - Change WiFi SSID and Password (Optional), click "Next".
- Wireless 5 GHz - Change WiFi SSID and Password (Optional), click "Next".
- Confirm - Check settings then click "Save".
Quick Start - VDSL Modem Router
- Click "Quick Setup".
- Start - Click "Next".
- Region and Time Zone - Choose "United Kingdom" and "(GMT)", click "Next".
- Operation Mode - Choose "xDSL Modem Router Mode", click "Next".
- Select ISP - From ISP List choose "VDSL_AAISP", click "Next".
- PPPoE - Enter broadband username and password, click "Next".
- Wireless 2.4 GHz - Change WiFi SSID and Password (Optional), click "Next".
- Wireless 5 GHz - Change WiFi SSID and Password (Optional), click "Next".
- Confirm - Check settings then click "Save".
Quick Start - PPPoE Router
- Click "Quick Setup".
- Start - Click "Next".
- Region and Time Zone - Choose "United Kingdom" and "(GMT)", click "Next".
- Operation Mode - Choose "Wireless Router Mode", click "Next".
- Ethernet WAN Type - Choose "PPPoE", click "Next".
- PPPoE - Enter broadband username and password, click "Next".
- Wireless 2.4 GHz - Change WiFi SSID and Password (Optional), click "Next".
- Wireless 5 GHz - Change WiFi SSID and Password (Optional), click "Next".
- Confirm - Check settings then click "Save".
Bridge - ADSL Modem
- Click "Network".
- Click "WAN Settings".
- Click "Add".
- DSL Modulation Type: ADSL
- VPI: 0
- VCI: 38
- Connection Type: Bridge
- Click "Save".
Bridge - VDSL Modem
- Click "Network".
- Click "WAN Settings".
- Click "Add".
- DSL Modulation Type: VDSL
- Enable VLAN ID: ✓
- VLAN ID: 101
- Connection Type: Bridge
- Click "Save".
Bridging Notes
- Firmware TD-W9980_V1_150507 07/05/15 does not support *at least* 1508 byte frames so as to allow RFC4638 PPPoE to a connected device. i.e., 1500 byte MTU is not possible when in bridge mode.
- AAISP contacted TP-Link regarding this 2015-09-12