Configuring a Siemens Gigaset phone for AAISP

Feature Notes
Supports 302 Redirect	No
Tested on FireBrick SIP Server	Yes
IPv6 Support	No

These notes are the same for configuring an S685IP, A580IP and N300A too.

Update to new firmware here https://gigaset.atlassian.net/wiki/display/GPPPO/N510+IP+PRO+Release+notes+42.192

If there are problems in setting up the base station it is easiest to start from a factory reset condition. This can be achieved by holding the blue button on the front of the base unit while power cycling it. After this the handset will need to be re-registered with the base unit (hold the blue button on the base unit while power cycling the handset). The pin should be changed from its default value of 0000 using the handset.

Starting from a factory reset, the following items need to be set using the web server in the base unit.

IP address

By default the base unit picks up an IP address using DHCP. This can be over-ridden by connecting to "Settings -> IP Configuration", selecting "Static" and filling in the address details as required. Then click on the "Set" button. By default, the device only allows access to it's web interface from the local subnet.

N300 and Voiceless

(Same on the S685IP / A580IP / N300A)

click to view settings

On the web interface, go to:

Settings -> Telephony -> Edit 1, Show Advanced Settings

Gigaset N300 Settings
Setting	Value
Connection Name or Number	AAISP (Or whatever you like)
Authentication Name	Your Number (+44...)
Authentication Password	Your Password
Username	Your Number (+44...)
Domain	voiceless.aa.net.uk
Proxy Server Address	blank
Registration server	voiceless.aa.net.uk
Registration refresh time	180

Then you'll need to assign this account to a handset for incoming calls, this is set under

Settings -> Telephony -> Number Assignment

Number Assignment

Don't forget to secure the base station with a new PIN:

Settings -> Management -> Miscellaneous -> New Pin

Audio settings

In menu:

Settings -> Telephony -> Audio" select "Voice Quality -> Own Codec preference".

For "IP1" (Or whatever you call the AAISP account) remove all codecs except "G.711 a law". This setting will generally give the best audio quality.

Other settings

If there are problems with recognition of DTMF tones by other systems consider setting "RFC2833" and avoid using "Audio". in the setting:

Settings -> Telephony -> Advanced Settings -> RFC2833

Check that the Number Plan/Assignment is set to use the VoIP rather than the fixed (pstn) line:

Settings - Number Assignment Set the VoIP for outgoing, and set the others to suit...

It may not say the above and Automatic negotiation of DTMF transmission will need to be Yes

Set the Tone Pattern to be UK:

Settings -> Management -> Local Settings -> Tone Pattern=United Kingdom

You may want to remove, or edit, the 'Info Services' - this is the information such as weather and so in that can be displayed on the screen:

Settings - Info Services

New Firmware available

Sometimes you may see a 'New Firmware available' message on the screen of the handset.

eg, Version 42.263 (422630000000 / V42.00) became available in March 2023

What Version

To view the version you are running, log in to the Base Station's web interface, and go to Status -> Device

How to upgrade when you have the message 'New Firmware available' :

Press the Envelope button under the screen.
- Screen will say 'Start download?'
- Click the button under 'Yes'
- Enter your pin - this is the same PIN that you'd use to access the Base Station's web interface
- Screen will say 'Firmware update in progress...'
The base station will install the upgrade - will take about a minute
The base station will reboot - will take a few minutes
- During this stage, the handset will say 'No Base'... wait a little while...
The handset will connect to the Base once the Base is back up and running

Manual Upgrade

On a handset you can try to upgrade manually:

Menu » Settings » System » Update Firmware.
Enter base station system PIN (default setting: 0000).
Press the display key "Yes" to start the download.

Quirks

We have seen odd things with a S685IP (Firmware version: 022270000000 / 043.00) where it would register, but not pass calls. A reboot of the base station fixed this.

Firewall & Security

You will also want to set up firewall rules, as per the VoIP Firewall page.
Also see the VoIP Security page for information about securing your VoIP service.