B10D Factory Reset: Difference between revisions

B10D Factory Reset (view source)

Revision as of 11:28, 24 July 2020

342 bytes added , 24 July 2020

m

→‎Reset to the ZyXEL Factory Settings

AA-Andrew

autoreview, Bureaucrats, editor, Interface administrators, reviewer, Administrators

12,270

edits

Revision as of 12:32, 30 June 2017 (view source) AA-Andrew (talk \| contribs) (Created page with "There are 4 configuration settings that the router can be in: {\| class="wikitable" \|- ! State !! Info !! How to apply \|- \| ZyXEL Factory Settings \|\| The actual state of the r...")		Revision as of 11:28, 24 July 2020 (view source) AA-Andrew (talk \| contribs) m (→‎Reset to the ZyXEL Factory Settings) Newer edit →
(11 intermediate revisions by the same user not shown)
__NOTOC__<indicator name="Front">[[File:Menu-cog.svg\|link=:Category:B10D Settings & Configuration\|30px\|Back up to the VMG1312-B10D settings Page]]</indicator> [[Category:B10D Settings & Configuration\|Factory Reset]] ==Overview== There are 4 configuration settings that the router can be in: {\| class="wikitable" \|- ! State !! ~~Info~~Information !! How to apply \|- \| ZyXEL Factory Settings \|\| The actual state of the router before AAISP apply their 'base' setting \|\| 'save_default clean' command via CLI. More info below \|- \| AAISP Base Settings (rom-d) \|\| As supplied by AAISP before the config for your line is applied, the settings allow the router to get online and obtain the specific configuration for your line \|\| Upload AAISP's rom-d file. Not usually required as it is usually already loaded by AAISP, More info below. \|- \| Configured by AAISP \|\| The settings for your specific line, along with settings as per the Control Pages \|\| Usually when first plugged in on a customer line. Or, Via the Control Pages, or by holding in reset for 5 sec. More info below \|- \| Customer Edited \|\| If customer makes further changes to their config after AAISP has sent the settings \|\| Restore from a backup you made previously #Switch router on, wait for it to boot up #With a paperclip, pen, etc., hold in the reset button #Wait until ~~power~~all ~~flashes~~the ~~red,~~LEDs ~~keep~~light ~~holding~~up itthen ~~down~~release ~~until~~the ~~power~~reset ~~stops flashing.~~button #Wait for the router to boot up again, the power light will flash whilst booting then go steady when ready ~~#Release the reset button~~ ~~#Wait for the router to boot up again~~ ==About the AAISP Base settings== <syntaxhighlight lang=bash highlight="1,6,7,8" lang="bash"> $ telnet 90192.~~155~~168.901.~~129~~1 Trying 90192.~~155~~168.901.~~129~~1... Connected to ~~brick~~192.h168.~~hearn~~1.~~org.uk~~1. Escape character is '^]'. VMG1312-B10A Login: supervisor Password: [your admin/supervisor password] > save_default clean ROM-D cleaned. </syntaxhighlight> You may need to obtain the supervisor password, which is specific for each device and not known by AAISP. At this point you can reset the router for this to be applied. The router will then boot up in its original factory settings without any of the AAISP configuration settings. You can reset the router by holding in the reset button for 5 seconds. bftpd:error:341.231:cmsImg_validateImage:1514:Could not determine image format [72063 bytes] Then this will be due to the Firmware version not matching the version that the config file was made for. See the [[VMG1312: Software\|Software Page]] for information about the software versions. ~~[[Category:ZyXEL VMG1312\|Reset]]~~