IPv6 Configuration: Difference between revisions

From AAISP Support Site
m (Link to more recent resource)
 
(3 intermediate revisions by 2 users not shown)
Line 1: Line 1:
'''June 2023 - this page, and the links, are probably somewhat dated now.'''

= Related Pages on the A&A Website =
= Related Pages on the A&A Website =


Line 6: Line 8:


*[http://www.pitt-pladdy.com/blog/_20100123-184109%2B0000%20OpenWrt%20with%20native%20IPv6%20on%20DG834%20v2%20%28using%20AAISP%29/ Using OpenWRT as an IPv6 router]
*[http://www.pitt-pladdy.com/blog/_20100123-184109%2B0000%20OpenWrt%20with%20native%20IPv6%20on%20DG834%20v2%20%28using%20AAISP%29/ Using OpenWRT as an IPv6 router]
*[http://wiki.openwrt.org/doc/howto/ipv6 Configuring OpenWRT for IPv6]
*[http://wiki.openwrt.org/doc/howto/ipv6 Configuring OpenWRT for IPv6] '''Ancient''' see [[OpenWRT routers]]
*[http://www.davidc.net/networking/ipv6-source-address-selection-linux IPv6 Source Address Selection on Linux]
*[http://www.davidc.net/networking/ipv6-source-address-selection-linux IPv6 Source Address Selection on Linux]
*[http://ipv6.raphnet.net/ Linux/BSD Configuration commands]
*[http://ipv6.raphnet.net/ Linux/BSD Configuration commands]
* https://support.aa.net.uk/DGA0122_No_IPv6
*[https://support.aa.net.uk/DGA0122_No_IPv6 The Technicolor DGA0122 router and IPv6 fixes]


== IPv6 ready hardware ==
== IPv6 ready hardware ==

Latest revision as of 12:54, 1 March 2024

June 2023 - this page, and the links, are probably somewhat dated now.

Related Pages on the A&A Website

Useful Blog/HOWTO Entries

IPv6 ready hardware

The following equipment has been successfully used as an IPv6 Router for home use. These are known as CPE or Customer Premises Equipment.

  • Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem
  • Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem Guide
  • Netgear DG834v2 running OpenWRT 8.09 (Kamikaze)
  • Linksys WRTU54G-TM running OpenWRT trunk build with a Netgear DM111P Modem
  • Netgear WNR854T running OpenWRT 10.03 (Backfire) with BT Openreach modem on FTTC
  • Cisco Devices running 12.4 and above
  • Our FireBrick 2700 page has info on Native IPv6 config (also applies to 2500)
  • Vigor 120 - earlier firmware versions have problems with IPv6
  • Billion BiPAC 7800N with firmware 1.06d
  • The MikroTik RouterOS page has information on IPv6 configuration

The search for additional IPv6 CPE possibilities: IPv6CPESearch

Native IPv6 Connections

IPv6 over IP Tunnelled Connections

See also the configuration examples on the IPv6 Knowledge-base page referenced above.

FireBrick 2500/2700

It's quite easy.... Assuming you have an IPv6 block allocated to your line on Clueless and you're using the FB for PPPoE, then all the FB config needs is:

  • An IPv6 address on the LAN subnet
  • ra="true" in the subnet