VoIP Phones - Gigaset N300: Difference between revisions

From AAISP Support Site
Line 1: Line 1:
=Configuring a Siemens S685IP for AAISP=
= [[Image:Gigaset-S685ip.jpg|right]]Configuring a Siemens S685IP for AAISP =


==Firewall settings:==
== Firewall settings: ==
Most probably, all outbound traffic will already be enabled, so it is just necessary to permit essential incoming
traffic to the S685IP. The following inbound settings are needed:


Most probably, all outbound traffic will already be enabled, so it is just necessary to permit essential incoming traffic to the S685IP. The following inbound settings are needed:
For SIP control data, allow UDP ports 5060 from 81.187.30.110-119


For RTP audio, allow UDP ports 5004-5020 from anywhere.
For SIP control data, allow UDP ports 5060 from 81.187.30.110-119


For RTP audio, allow UDP ports 5004-5020 from anywhere.
Use a good password and consider using IP lockdown on the AAISP control pages to help prevent fraudulent use!


Use a good password and consider using IP lockdown on the AAISP control pages to help prevent fraudulent use!
==Configuring the S685IP==


== Configuring the S685IP ==
If there are problems in setting up the S685IP it is easiest to start from a factory reset condition. This can
be achieved by holding the blue button on the front of the base unit while power cycling it. After this the
handset will need to be re-registered with the base unit (hold the blue button on the base unit while power
cycling the handset). The pin should be changed from its default value of 0000 using the handset.


If there are problems in setting up the S685IP it is easiest to start from a factory reset condition. This can be achieved by holding the blue button on the front of the base unit while power cycling it. After this the handset will need to be re-registered with the base unit (hold the blue button on the base unit while power cycling the handset). The pin should be changed from its default value of 0000 using the handset.
Starting from a factory reset, the following items need to be set using the web server in the base unit.


Starting from a factory reset, the following items need to be set using the web server in the base unit.
===IP address: ===
By default the base unit picks up an ip address using DHCP. This can be over-ridden by
connecting to "Settings -> IP Configuration", selecting "Static" and filling in the address details as required.
Then click on the "Set" button.


=== IP address: ===


By default the base unit picks up an ip address using DHCP. This can be over-ridden by connecting to "Settings -> IP Configuration", selecting "Static" and filling in the address details as required. Then click on the "Set" button.
===Registration with AAISP:===
Select menu "Settings -> Telephony -> Connections" and click the "Edit" button for
IP1. Then click the "Show Advanced Settings" button and fill in the following fields:


<br>
'''Authentication Name: <aaisp phone number> '''
(this can be in either UK or international format, for example
+44203095nnnn or 0203095nnnn )


=== Registration with AAISP: ===
''Authentication password: <password> ''
(This is the same password that is set on the AAISP control pages for this number. Some non-alphanumeric characters can cause registration failure. In particular avoid "#" and "/")


Select menu "Settings -&gt; Telephony -&gt; Connections" and click the "Edit" button for IP1. Then click the "Show Advanced Settings" button and fill in the following fields:
'''Username:''' <aaisp phone number>


'''Authentication Name: &lt;aaisp phone number&gt; ''' (this can be in either UK or international format, for example +44203095nnnn or 0203095nnnn )
'''Domain:''' proxy.aasip.co.uk (Don't accidentally type aaisp!)


''Authentication password: &lt;password&gt; '' (This is the same password that is set on the AAISP control pages for this number. Some non-alphanumeric characters can cause registration failure. In particular avoid "#" and "/")
'''Proxy server address:''' proxy.aasip.co.uk


'''Username:''' &lt;aaisp phone number&gt;
'''Registrar server:''' proxy.aasip.co.uk


'''Domain:''' proxy.aasip.co.uk (Don't accidentally type aaisp!)
All the other fields can be left as they are unless you are using NAT in which case the "Stun enabled" button
should be selected and the "Stun server" set to stun.aaisp.net


'''Proxy server address:''' proxy.aasip.co.uk
When everything is entered click on the "Set" button. The display will return to the "Settings -> Telephony ->
Connections" menu. Check that "IP1" is active and that the status is "Registered". You may wish to disable
"Gigaset.net" in this menu. It should now be possible to make and receive calls.


'''Registrar server:''' proxy.aasip.co.uk
=== Audio settings:===
In menu "Settings -> Telephony -> Audio" select "Voice Quality - Own Codec preference". For "IP1" remove all
codecs except "G.711 a law". This setting will generally give the best audio quality.


All the other fields can be left as they are unless you are using NAT in which case the "Stun enabled" button should be selected and the "Stun server" set to stun.aaisp.net
=== Other settings:===

If there are problems with recognition of dtmf tones by other systems consider setting "RFC2833" in the "Settings
When everything is entered click on the "Set" button. The display will return to the "Settings -&gt; Telephony -&gt; Connections" menu. Check that "IP1" is active and that the status is "Registered". You may wish to disable "Gigaset.net" in this menu. It should now be possible to make and receive calls.
-> Telephony -> Advanced Settings" menu. Avoid using "Audio".

=== Audio settings: ===

In menu "Settings -&gt; Telephony -&gt; Audio" select "Voice Quality - Own Codec preference". For "IP1" remove all codecs except "G.711 a law". This setting will generally give the best audio quality.

=== Other settings: ===

If there are problems with recognition of dtmf tones by other systems consider setting "RFC2833" in the "Settings -&gt; Telephony -&gt; Advanced Settings" menu. Avoid using "Audio".

Revision as of 12:51, 9 December 2010

Gigaset-S685ip.jpg
Configuring a Siemens S685IP for AAISP

Firewall settings:

Most probably, all outbound traffic will already be enabled, so it is just necessary to permit essential incoming traffic to the S685IP. The following inbound settings are needed:

For SIP control data, allow UDP ports 5060 from 81.187.30.110-119

For RTP audio, allow UDP ports 5004-5020 from anywhere.

Use a good password and consider using IP lockdown on the AAISP control pages to help prevent fraudulent use!

Configuring the S685IP

If there are problems in setting up the S685IP it is easiest to start from a factory reset condition. This can be achieved by holding the blue button on the front of the base unit while power cycling it. After this the handset will need to be re-registered with the base unit (hold the blue button on the base unit while power cycling the handset). The pin should be changed from its default value of 0000 using the handset.

Starting from a factory reset, the following items need to be set using the web server in the base unit.

IP address:

By default the base unit picks up an ip address using DHCP. This can be over-ridden by connecting to "Settings -> IP Configuration", selecting "Static" and filling in the address details as required. Then click on the "Set" button.


Registration with AAISP:

Select menu "Settings -> Telephony -> Connections" and click the "Edit" button for IP1. Then click the "Show Advanced Settings" button and fill in the following fields:

Authentication Name: <aaisp phone number> (this can be in either UK or international format, for example +44203095nnnn or 0203095nnnn )

Authentication password: <password> (This is the same password that is set on the AAISP control pages for this number. Some non-alphanumeric characters can cause registration failure. In particular avoid "#" and "/")

Username: <aaisp phone number>

Domain: proxy.aasip.co.uk (Don't accidentally type aaisp!)

Proxy server address: proxy.aasip.co.uk

Registrar server: proxy.aasip.co.uk

All the other fields can be left as they are unless you are using NAT in which case the "Stun enabled" button should be selected and the "Stun server" set to stun.aaisp.net

When everything is entered click on the "Set" button. The display will return to the "Settings -> Telephony -> Connections" menu. Check that "IP1" is active and that the status is "Registered". You may wish to disable "Gigaset.net" in this menu. It should now be possible to make and receive calls.

Audio settings:

In menu "Settings -> Telephony -> Audio" select "Voice Quality - Own Codec preference". For "IP1" remove all codecs except "G.711 a law". This setting will generally give the best audio quality.

Other settings:

If there are problems with recognition of dtmf tones by other systems consider setting "RFC2833" in the "Settings -> Telephony -> Advanced Settings" menu. Avoid using "Audio".