12,271
edits
VoIP Phones - Yealink DECT: Difference between revisions
m
no edit summary
mNo edit summary |
|||
| (18 intermediate revisions by 2 users not shown) | |||
|
<indicator name="VoIPConfiguring">[[File:menu-voip.svg|link=:Category:VoIP Phones|30px|Back up to the VoIP Configuring page]]</indicator>
[[Image:W53P-1.png|thumb|Yealink W60B base and handset]]
= Configuring Yealink DECT phone for AAISP =
*PoE or Mains plug for power
*Transfer button (allows assisted or blind transfers to other SIP extensions/external numbers)
*Docs/firmware from Yealink: https://support.yealink.com/en/portal/docList?archiveType=document&productCode=b0040cca269c2a01
*[https://www.yealink.com/upfiles/products/datasheet/Yealink-W60B-Datasheet.pdf Datasheet]
|contact us
|}
The PIN is used to register handsets to the base station, and for the handset to access settings from the base station. When a Base and a handset are supplied together in a single box, then the handset should already be registered to the base station. You can use these steps to register additional handsets though:
=Registering an additional Handset=▼
# Power up handset▼
# Press the button under 'Reg'▼
# Hold the 'Radio' button on the Base for 3 seconds▼
# Handset should then initialise▼
# Go to the Base station UI and set up the new account:▼
# Account - Number Assignment - or set up a new account:▼
## Account - Set Account2 --> Fill in details▼
## Account - Handset name --> Set the name▼
<gallery widths=200px heights=200px mode="nolines">▼
</gallery>▼
= Find the IP address of the Base station & login to setup web pages. =
By default the Yealink base unit picks up an IP address using DHCP. You can find the IP address from the Handset as follows:
File:Hansetbase.jpg|3.2 Select Base and press Ok
File:Handsetipadd.jpg|3.3 Under IPv4 you will see the IP address.
▲</gallery>
▲=Registering an additional Handset=
▲# Power up handset
▲# Press the button under 'Reg'
▲# Hold the button on the Base for 3 seconds
▲# Handset should then initialise
▲# Go to the Base station UI and set up the new account:
▲# Account - Number Assignment - or set up a new account:
▲## Account - Set Account2 --> Fill in details
▲## Account - Handset name --> Set the name
▲<gallery widths=200px heights=200px mode="nolines">
▲File:W73pbase.jpg|2.1.Radio Button on Base Unit
▲File:Handsetsettings.jpg|2.4. Scroll to Settings & press Ok.
▲File:Handsetreg.jpg|2.5. Arrow down to 6.Registration the press Ok.
▲File:Handsetreg2.jpg|2.6. Press Register Handset.
</gallery>
Status -> Handset & VoIP
You should the the account Status as 'Registered'
<gallery widths=300px heights=300px mode="nolines" caption="Screenshot of Account registration page">
Yealink_W53P_SIP_Config.png|VoIP Account settings▼
</gallery>
===Handset Assignment===
You have the flexibility to decide which VoIP account should ring which handset, and also which account the handsets use to make their outgoing calls.
<gallery mode="packed" widths=250px heights=250px mode="nolines" caption="Screenshots of number assignment page">
▲Yealink_W53P_SIP_Config.png|VoIP Account settings
▲Yealink W53P Hanset Assignment.png|Number Assignment
Yealink-4handsets1number.png|Four Handsets sharing one VoIP Account
</gallery>
OK --> Call Features (orange) --> Do Not Disturb
==Factory reset the Yealink DECT Base Station==▼
=Registering an additional Handset=▼
# Power up handset▼
# Press the button under 'Reg'▼
# Hold the button on the Base for 3 seconds▼
# Handset should then initialise▼
# Go to the Base station UI and set up the new account:▼
# Account - Number Assignment - or set up a new account:▼
## Account - Set Account2 --> Fill in details▼
## Account - Handset name --> Set the name▼
If you have lost the password you will have to factory reset the base station, and the default username and password will then work, and you'll need to configure the unit again.
There are a few ways to factory reset the Yealink base station:
===From web ui===
If you know the password!
Settings -> Upgrade --> Reset
# Wait a further 5 minutes
# Then, reboot the base station by unplugging it from power and plugging it back in
▲=Registering an additional Handset=
▲# Power up handset
▲# Press the button under 'Reg'
▲# Hold the button on the Base for 3 seconds
▲# Handset should then initialise
▲# Go to the Base station UI and set up the new account:
▲# Account - Number Assignment - or set up a new account:
▲## Account - Set Account2 --> Fill in details
▲## Account - Handset name --> Set the name
[[Category:VoIP Phones|
| |||