Latest revision as of 00:22, 18 August 2018

AAISP configure routers via TR-069 protocol. We generate a config file and this is sent to the router. Firmware updates are also able to be sent to the router.

Customers are free to alter the configuration as supplied, sending a configuration from the Control Pages will overwrite any settings changed though.

Here is an overview of the settings that are modified from the default, you can sort the table by the date added column to see any new changes.

Area	Setting	Note	Date added
Broadband	Configure WAN interface	Further Settings on Control Pages: ADSL/FTTC, Bridge or WAN on port 4 (FTTP)	2015-02-01
Broadband	Configure WAN VLAN 802.1q=101	Only for the VDSL WAN interface.	2015-02-01
Broadband	Configure PPP	Settings as per the service	2015-02-01
Home Network	Configure DHCP	Further Settings on Control Pages, Default=All IPs using AAISP DNS servers or as set on Control Pages	2015-02-01
Home Network	Configure LAN subnet	If line has a block of public IPs use them, else default is 192.168.1.1	2015-02-01
Home Network	Configure LAN subnet	If router set for bridge mode, leave IP as 192.168.1.1	2015-06-19
Wireless	Configure WiFi	Further Settings on Control Pages: SSID, Password or disable WiFi	2015-02-01
Wireless	Configure WiFi for 20 MHz	Instead of 40 MHz see VMG1312: WiFi Tips	2015-02-01
Wireless	Configure WiFi for AES only	This disables legacy/insecure TKIP see VMG1312: WiFi Tips	2015-06-16
Firewall	Configure Firewall on/off	Settings on Control Pages, Default=Enabled	2015-02-01
TR-069	Configure TR-069	Allows the router to be managed by AAISP, we give customer the same controls as staff get	2015-02-01
Log	Configure Local logging	Logs: System, PPPoE, XDSL, Internet, Attack, Account.	2015-05-29
Firewall	Rule to allow ICMPv6 to LAN	Helps make IPv6 work!	2015-06-16
Home Network	Disable NAT	If customer has a public IP block	2015-02-01
Maintenance	Disable SNMP	SNMP has a habit of having vulnerabilities, we are not aware of any for the VMG1312 though	2015-02-01
Maintenance	Disable 3G backup	Not usually required	2015-02-01
Firewall	Disable 'DoS Protection Blocking'	It does odd things, like blocking WebUI over WiFi!	2015-06-16
Maintenance	Change NTP servers	time.aa.net.uk and 0.uk.pool.ntp.org	2015-02-01
Maintenance	Change 'supervisor' password	Setting on Control Pages (same as admin)	2015-02-01
Maintenance	Change 'admin' password	Setting on Control Pages	2015-02-01
Firewall	Change Remote Management Options	Further Settings on Control Pages. Default is to only allow the LAN and the AAISP offices access.	2015-02-01
QoS	Change QoS	Set to give upstream priority based on 'Packet Length' See: VMG1312: QoS	2015-02-01
Firewall	Change 'Deny Ping Response' to Disable,	Allows the router to reply to pings	2015-02-01
QoS	Disable the default QoS Classes	See: VMG1312: QoS	2015-02-01
Maintenance	Remove zyuser user	It is a default read-only user, there is no need for it	2015-02-01

Static routes are currently not configured. (Only applicable if you have multiple public IP blocks and need them routed to a secondary router. These can be configured manually though.

This list may not be exhaustive, and may change over time.

WAN Configuration

As mentioned above, the WAN side of the router is configured depending on the Service provided and the settings on the Control Pages.

Service	Bridge	WAN port	Note: WAN	Note: LAN	Note: WiFi	Other notes
Routing Configurations - Connecting to phone line
ADSL	No	DSL	Plugs in to phone line	Customer LAN	Customer LAN	MTU 1492
FTTC wires only	No	DSL	Plugs in to phone line	Customer LAN	Customer LAN	MTU 1492, WAN VLAN 802.1q=101
Routing Configurations - Connecting to another modem
FTTC engineer install (not available for new installations)	No	Port 4	plugs in to Openreach modem (no longer supplied)	Customer LAN	Customer LAN	1492 MTU, WAN VLAN 802.1q=101. QoS will not know the uplink speed automatically, The rate can be set under Network Setting - Broadband - #3 edit
FTTP	No	Port 4	plugs in to Openreach modem	Customer LAN	Customer LAN	1492 MTU. QoS will not know the uplink speed automatically, The rate can be set under Network Setting - Broadband - #3 edit
Bridge Configurations
FTTC wires only with Customer own PPPoE router	Yes	DSL	Plugs in to phone line	Customer PPPoE router	Usually Disabled	ZyXEL becomes a bridging modem. MTU 1492. WAN VLAN 802.1q=101
ADSL with Customer own PPPoE router	Yes	DSL	Plugs in to phone line	Customer PPPoE router	Usually Disabled	ZyXEL becomes a bridging modem. MTU 1492

Making Changes

If you make changes to your configuration then you may want to back it up. See: VMG1312: Backup Configuration

@@ Line 10: / Line 10: @@
 |-
 | Broadband || Configure WAN interface || Further Settings on Control Pages: ADSL/FTTC, Bridge or WAN on port 4 (FTTP) || 2015-02-01
+|-
+|  Broadband || Configure WAN VLAN 802.1q=101 || Only for the VDSL WAN interface. || 2015-02-01
 |-
 |  Broadband || Configure PPP || Settings as per the service || 2015-02-01
@@ Line 21: / Line 23: @@
 |  Wireless || Configure WiFi || Further Settings on Control Pages: SSID, Password or disable WiFi || 2015-02-01
 |-
-|  Wireless || Configure WiFi for 20Mhz || Instead of 40Mhz see [[VMG1312: WiFi Tips]] || 2015-02-01
+|  Wireless || Configure WiFi for 20&nbsp;MHz || Instead of 40&nbsp;MHz see [[VMG1312: WiFi Tips]] || 2015-02-01
 |-
 |  Wireless || Configure WiFi for AES only|| This disables legacy/insecure TKIP  see [[VMG1312: WiFi Tips]] || 2015-06-16
@@ Line 47: / Line 49: @@
 |  Maintenance || Change 'admin' password || Setting on Control Pages || 2015-02-01
 |-
-|  Firewall || Change Remote Management Options || Further Settings on Control Pages || 2015-02-01
+|  Firewall || Change Remote Management Options || Further Settings on Control Pages. Default is to only allow the LAN and the AAISP offices access. || 2015-02-01
 |-
 |  QoS || Change QoS || Set to give upstream priority based on 'Packet Length' See: [[VMG1312: QoS]] || 2015-02-01
@@ Line 58: / Line 60: @@
 |}
-*Static routes are currently not configured. (Only applicable if you have multiple public IP blocks and need them routed to a secondary router. These can be configured manually though.
+*[[VMG1312: Static Routes|Static routes]] are currently not configured. (Only applicable if you have multiple public IP blocks and need them routed to a secondary router. These can be configured manually though.
 This list may not be exhaustive, and may change over time.
@@ Line 86: / Line 88: @@
 |MTU 1492
 |----
-!FTTC engineer install
+!FTTC wires only
 |No
+|DSL
-|Port 4
-|plugs in to Openreach modem
+|Plugs in to phone line
 |Customer LAN
 |Customer LAN
+|MTU 1492, WAN VLAN 802.1q=101
-|1492 MTU. QoS will not know the uplink speed automatically, The rate can be set under Network Setting - Broadband - #3 edit
 |----
+!colspan="7"|Routing Configurations - Connecting to another modem
-!FTTC wires only
+|----
+!FTTC engineer install (not available for new installations)
 |No
+|Port 4
-|DSL
+|plugs in to Openreach modem (no longer supplied)
-|Plugs in to phone line
 |Customer LAN
 |Customer LAN
+|1492 MTU, WAN VLAN 802.1q=101. QoS will not know the uplink speed automatically, The rate can be set under Network Setting - Broadband - #3 edit
-|MTU 1492
 |----
 !FTTP
@@ Line 118: / Line 122: @@
 |Customer PPPoE router
 |Usually Disabled
-|ZyXEL becomes a bridging modem. MTU 1492
+|ZyXEL becomes a bridging modem. MTU 1492. WAN VLAN 802.1q=101
 |----
 !ADSL with Customer own PPPoE router
@@ Line 130: / Line 134: @@
 |}
+=Making Changes=
+If you make changes to your configuration then you may want to back it up. See: [[VMG1312: Backup Configuration]]
-[[Category:ZyXEL_VMG1312|AAISP Configuration]]
+[[Category:ZyXEL VMG1312-B10A|AAISP Configuration]]