Latest revision as of 12:54, 1 March 2024

June 2023 - this page, and the links, are probably somewhat dated now.

Related Pages on the A&A Website

www.aaisp.net.uk/kb-broadband-ipv6.html

Useful Blog/HOWTO Entries

IPv6 ready hardware

The following equipment has been successfully used as an IPv6 Router for home use. These are known as CPE or Customer Premises Equipment.

Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem
Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem Guide
Netgear DG834v2 running OpenWRT 8.09 (Kamikaze)
Linksys WRTU54G-TM running OpenWRT trunk build with a Netgear DM111P Modem
Netgear WNR854T running OpenWRT 10.03 (Backfire) with BT Openreach modem on FTTC
Cisco Devices running 12.4 and above
Our FireBrick 2700 page has info on Native IPv6 config (also applies to 2500)
Vigor 120 - earlier firmware versions have problems with IPv6
Billion BiPAC 7800N with firmware 1.06d
The MikroTik RouterOS page has information on IPv6 configuration

The search for additional IPv6 CPE possibilities: IPv6CPESearch

Juniper SRX series of routers

Native IPv6 Connections

Cisco IPv6 Native Config
IPv6 - How AAISP manage IPv6 on Broadband lines.

IPv6 over IP Tunnelled Connections

See also the configuration examples on the IPv6 Knowledge-base page referenced above.

FireBrick 2500/2700

It's quite easy.... Assuming you have an IPv6 block allocated to your line on Clueless and you're using the FB for PPPoE, then all the FB config needs is:

An IPv6 address on the LAN subnet
ra="true" in the subnet

@@ Line 1: / Line 1: @@
+'''June 2023 - this page, and the links, are probably somewhat dated now.'''
-= Related Pages on the A&amp;A Website:  =
+= Related Pages on the A&amp;A Website  =
 *[http://www.aaisp.net.uk/kb-broadband-ipv6.html www.aaisp.net.uk/kb-broadband-ipv6.html]
@@ Line 6: / Line 8: @@
 *[http://www.pitt-pladdy.com/blog/_20100123-184109%2B0000%20OpenWrt%20with%20native%20IPv6%20on%20DG834%20v2%20%28using%20AAISP%29/ Using OpenWRT as an IPv6 router]
-*[http://wiki.openwrt.org/doc/howto/ipv6 Configuring OpenWRT for IPv6]
+*[http://wiki.openwrt.org/doc/howto/ipv6 Configuring OpenWRT for IPv6] '''Ancient''' see [[OpenWRT routers]]
+*[http://www.davidc.net/networking/ipv6-source-address-selection-linux IPv6 Source Address Selection on Linux]
+*[http://ipv6.raphnet.net/ Linux/BSD Configuration commands]
+*[https://support.aa.net.uk/DGA0122_No_IPv6 The Technicolor DGA0122 router and IPv6 fixes]
-== Consumer CPE Equipment  ==
+== IPv6 ready hardware  ==
-The following equipment has been successfully used as an IPv6 Router for home use
+The following equipment has been successfully used as an IPv6 Router for home use.  These are known as CPE or Customer Premises Equipment.
 *Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem
+*Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem [[IPv6 SpeedTouch|Guide]]
 *Netgear DG834v2 running OpenWRT 8.09 (Kamikaze)
+*Linksys WRTU54G-TM running OpenWRT trunk build with a Netgear DM111P Modem
+*Netgear WNR854T running OpenWRT 10.03 (Backfire) with BT Openreach modem on FTTC
+*[[Router - Cisco IPv6 IOS Versions|Cisco Devices]] running 12.4 and above
+*Our [[FireBrick 2700]] page has info on Native IPv6 config (also applies to 2500)
+*[[Vigor 120]] - earlier firmware versions have problems with IPv6
+*Billion BiPAC 7800N with firmware 1.06d
+*The MikroTik [[RouterOS]] page has information on IPv6 configuration
+The search for additional IPv6 CPE possibilities: [[IPv6CPESearch]]
+* [[Router - Juniper SRX|Juniper SRX]] series of routers
+== Native IPv6 Connections ==
+*[[Cisco IPv6 Native Config]]
+*[[IPv6]] - How AAISP manage IPv6 on Broadband lines.
 == IPv6 over IP Tunnelled Connections  ==
@@ Line 19: / Line 39: @@
 *[[Cisco IPv6 Tunnel Config]]
 *[[FreeBSD IPv6 Tunnel Config]]
+*[[FireBrick 2700 v6 Tunnel]]
+*[[Debian IPv6 Tunnel Config]]
+*[[Linux NetworkManager IPv6 Tunnel Config]]
 See also the configuration examples on the IPv6 Knowledge-base page referenced above.