Jump to content

This is the support site for Andrews & Arnold Ltd, a UK Internet provider. Information on these pages is generally for our customers but may be useful to others, enjoy!

Ethernet IP Settings: Difference between revisions

← Older edit
Content deleted Content added
AA-Andrew (talk | contribs)
autoreview, Bureaucrats, editor, Interface administrators, reviewer, Administrators
12,616 edits
AA-Andrew (talk | contribs)
autoreview, Bureaucrats, editor, Interface administrators, reviewer, Administrators
12,616 edits
 
(14 intermediate revisions by the same user not shown)
Line 1: Line 1:
__NOTOC__<indicator name="Front">[[File:Menu-ethernet.svg|link=:Category:Ethernet|30px|Back up to the Ethernet Services Page]]</indicator>
<indicator name="Front">[[File:Menu-ethernet.svg|link=:Category:Ethernet|30px|Back up to the Ethernet Services Page]]</indicator>
This information is in relation to our Etherway/Etherflow services.
This information is in relation to our Etherway/Etherflow services.


==IP settings==
==IP settings==

PPP or PPPoE is not used on Ethernet services. Instead a direct IP interlink subnet between A&A routers and the customer's router.

The Ethernet link provides a connection between your network and ours, and we connect your network to the internet. To achieve this we provide IP addresses on the link. A block of IP addresses is used specifically to link between us, and then additional addresses are provided as needed for your network.
The Ethernet link provides a connection between your network and ours, and we connect your network to the internet. To achieve this we provide IP addresses on the link. A block of IP addresses is used specifically to link between us, and then additional addresses are provided as needed for your network.


Line 30: Line 33:
|}
|}


⚫
When configuring your router/firewall you must pick one of the three addresses that are for you use, and set the subnet mask to 255.255.255.248. The gateway is set to the first usable address - the virtual gateway.
⚫
[[File:Eth-link.png|none|frame]]

⚫
When configuring your router/firewall you must pick one of the three addresses that are for you use, and set the subnet mask to 255.255.255.248. The gateway is set to the first usable address - the virtual gateway. DNS is set to 217.169.20.20 and 217.169.20.21.


You should not use the "A" or "B" router address directly for anything except BGP (see below). The virtual gateway will be the same as either "A" or "B" routers, and we may switch this at any time and disable one or other of the two real routers for maintenance or in the event of failure at any time without notice. What we aim to do is always ensure you have a working virtual gateway and hence an internet connection.
You should not use the "A" or "B" router address directly for anything except BGP (see below). The virtual gateway will be the same as either "A" or "B" routers, and we may switch this at any time and disable one or other of the two real routers for maintenance or in the event of failure at any time without notice. What we aim to do is always ensure you have a working virtual gateway and hence an internet connection.
Line 54: Line 55:
|}
|}


You can set DNS manually to 2001:8b0::2020 and 2001:8b0::2021.

⚫
==Dual routers and VRRP==
⚫
If you wish to run two routers yourself and use a protocol such as VRRP, set the virtual address as the last usable address. You can use the other two addresses as the real addresses of your two routers. We use VRID 42 for VRRP so use a different VRID if you are using VRRP to avoid any clash.


==Additional IP blocks==
==Additional IP blocks==
If you have additional IP requirements, these will be set up on your control pages and you can change the target address if you need. We will set these up to route to your gateway address initially, assuming (for IPv4) that you are using the last usable address as your firewall/router.
If you have additional IP requirements, these will be set up on your control pages and you can change the target address if you need. We will set these up to route to your gateway address initially, assuming (for IPv4) that you are using the last usable address as your firewall/router.


⚫
[[File:Eth-link.png|800px]]
⚫
==DSL Fallback==
⚫
Customers with an Ethernet circuit can also have one or more DSL circuits, and the IP block(s) can be configured to fall back to DSL in the case of the Ethernet going down.


==DNS resolvers==
Usually this can be setup by staff, but this is all managed on the IP settings for addresses attached to a DSL circuit. The routing options allow priorities, and so the first priority can be the IP of the interlink you have on the Ethernet, and the second routing can be the DSL circuits.
You can use our usual DNS resolvers:
[[File:IP-Routing-EthernetFallback.png|none|frame|Fallback IP settings]]
*217.169.20.20
*217.169.20.21
*2001:8b0::2020
*2001:8b0::2021

⚫
==Dual routers and VRRP==
⚫
If you wish to run two routers yourself and use a protocol such as VRRP, set the virtual address as the last usable address. You can use the other two addresses as the real addresses of your two routers. We use VRID 42 for VRRP so use a different VRID if you are using VRRP to avoid any clash.

⚫
==DSL or L2TP Fallback==
⚫
Customers with an Ethernet circuit can also have one or more DSL circuits or a L2TP service, and the IP block(s) can be configured to fall back to DSL/L2TP in the case of the Ethernet going down.

This can be setup by staff, do get in touch.


==BGP==
==BGP==
If you are announcing addresses to us using BGP then the routing and fall-back is managed by BGP. You should set up your BGP routers to peer with the two real router addresses ("A" and "B"). If you have two BGP routers then set up a full mesh (4 peer links). In the event of any maintenance we will cleanly close BGP sessions first causing routing to switch as necessary. You will need a suitable IP assignment and AS number for BGP. We support 32 bit AS numbers.
If you are announcing addresses to us using BGP then the routing and fall-back is managed by BGP. You should set up your BGP routers to peer with the two real router addresses ("A" and "B"). If you have two BGP routers then set up a full mesh (4 peer links). In the event of any maintenance we will cleanly close BGP sessions first causing routing to switch as necessary. You will need a suitable IP assignment and AS number for BGP. We support 32 bit AS numbers. See: [https://www.aa.net.uk/broadband/byoip/ Bring your own IP]


==Firewall==
==Firewall==
Line 84: Line 92:


We will normally set up a ping to one of your addresses and provide a graph showing loss and latency on the link from each of our routers. This can be useful in debugging any issues with the fibre or your router.
We will normally set up a ping to one of your addresses and provide a graph showing loss and latency on the link from each of our routers. This can be useful in debugging any issues with the fibre or your router.

Please set your firewall/router to allow pings from the three IP address on 'our' side of the interlink /29 block.


==Multiple links==
==Multiple links==
Retrieved from "http://support.aa.net.uk/Ethernet_IP_Settings"