FireBrick to FireBrick IPsec (Howto): Difference between revisions
(Prettyful colours) |
m (clean up, typos fixed: eg: → e.g.: (4)) |
||
| Line 1: | Line 1: | ||
<indicator name="Tunnels">[[File:Menu-IPsec.svg|link=:Category: |
<indicator name="Tunnels">[[File:Menu-IPsec.svg|link=:Category:FireBrick IPsec|30px|Back up to the FireBrick IPsec Tunnels Category Page]]</indicator> |
||
Here we will use an IPsec tunnel between two FireBricks. We will use IKEv2 and use a preshared-secret password. |
Here we will use an IPsec tunnel between two FireBricks. We will use IKEv2 and use a preshared-secret password. |
||
| Line 7: | Line 7: | ||
Do read the official FireBrick manuals for more information - this is just a simple howto covering the basics. |
Do read the official FireBrick manuals for more information - this is just a simple howto covering the basics. |
||
==Network Overview |
==Network Overview== |
||
{| class="wikitable" |
{| class="wikitable" |
||
| Line 33: | Line 33: | ||
</syntaxhighlight> |
</syntaxhighlight> |
||
If you firewall WAN to 'Self' (The FireBrick), then a firewall filter may be needed too, |
If you firewall WAN to 'Self' (The FireBrick), then a firewall filter may be needed too, e.g.: |
||
<syntaxhighlight lang=xml> |
<syntaxhighlight lang=xml> |
||
| Line 39: | Line 39: | ||
</syntaxhighlight> |
</syntaxhighlight> |
||
You will also want to add firewall rules to allow traffic between the two LANs, |
You will also want to add firewall rules to allow traffic between the two LANs, e.g., this will allow all traffic to and from Reading and will not NAT the traffic: |
||
<syntaxhighlight lang=xml> |
<syntaxhighlight lang=xml> |
||
| Line 57: | Line 57: | ||
</syntaxhighlight> |
</syntaxhighlight> |
||
If you firewall WAN to 'Self' (The Firebrick), then a firewall filter may be needed too, |
If you firewall WAN to 'Self' (The Firebrick), then a firewall filter may be needed too, e.g.: |
||
<syntaxhighlight lang=xml> |
<syntaxhighlight lang=xml> |
||
| Line 63: | Line 63: | ||
</syntaxhighlight> |
</syntaxhighlight> |
||
You will also want to add firewall rules to allow traffic between the two LANs, |
You will also want to add firewall rules to allow traffic between the two LANs, e.g., this will allow all traffic to and from London and will not NAT the traffic: |
||
<syntaxhighlight lang=xml> |
<syntaxhighlight lang=xml> |
||
| Line 73: | Line 73: | ||
This rule actually allows all traffic from all IPSec connections - so do edit to suit your environment. |
This rule actually allows all traffic from all IPSec connections - so do edit to suit your environment. |
||
[[Category: |
[[Category:FireBrick IPsec|FireBrick]] |
||
Latest revision as of 23:59, 14 March 2017
Here we will use an IPsec tunnel between two FireBricks. We will use IKEv2 and use a preshared-secret password.
Note that the password shown in the config entries below is an example only. A strong passphrase should be used in a real config.
Manuals
Do read the official FireBrick manuals for more information - this is just a simple howto covering the basics.
Network Overview
| FireBrick London | FireBrick Reading | |
|---|---|---|
| LAN IP range | 192.168.0.0/24 | 10.0.0.0/24 |
| WAN Address | 203.0.113.1 | 198.51.100.1 |
We'll want to end up with machines on each LAN being able to contact each other.
FireBrick London Config
<ipsec-ike comment="toReading">
<connection name="toReading" local-ip="203.0.113.1" peer-ips="198.51.100.1" graph="ReadingIPsec" routes="10.0.0.0/24" local-ID="1" peer-ID="1" auth-method="Secret" secret="mySecretPassword" mode="Immediate" blackhole="true"/>
</ipsec-ike>
If you firewall WAN to 'Self' (The FireBrick), then a firewall filter may be needed too, e.g.:
<rule name="IPsec from London FB" protocol="50" action="accept" source-ip="198.51.100.1"/>
You will also want to add firewall rules to allow traffic between the two LANs, e.g., this will allow all traffic to and from Reading and will not NAT the traffic:
<rule-set name="IPsec" source-interface="LAN ipsec" target-interface="LAN ipsec" no-match-action="continue" comment="Allow all traffic ">
<rule name="Allow" set-graph="IPSecTraffic" action="accept" set-nat="false" />
</rule-set>
This rule actually allows all traffic from all IPSec connections - so do edit to suit your environment.
FireBrick Reading Config
<ipsec-ike comment="toLondon">
<connection name="toLondon" local-ip="198.51.100.1" peer-ips="203.0.113.1" graph="LondonIPsec" routes="192.168.0.0/24" local-ID="1" peer-ID="1" auth-method="Secret" secret="mySecretPassword" mode="Immediate" blackhole="true"/>
</ipsec-ike>
If you firewall WAN to 'Self' (The Firebrick), then a firewall filter may be needed too, e.g.:
<rule name="IPsec from Reading FB" protocol="50" action="accept" source-ip="203.0.113.1"/>
You will also want to add firewall rules to allow traffic between the two LANs, e.g., this will allow all traffic to and from London and will not NAT the traffic:
<rule-set name="IPsec" source-interface="LAN ipsec" target-interface="LAN ipsec" no-match-action="continue" comment="Allow all traffic ">
<rule name="Allow" set-graph="IPSecTraffic" action="accept" set-nat="false" />
</rule-set>
This rule actually allows all traffic from all IPSec connections - so do edit to suit your environment.