IPv6 Configuration: Difference between revisions
(Added link to Juniper SRX page) |
(clean up) |
||
| Line 1: | Line 1: | ||
= Related Pages on the A&A Website |
= Related Pages on the A&A Website = |
||
*[http://www.aaisp.net.uk/kb-broadband-ipv6.html www.aaisp.net.uk/kb-broadband-ipv6.html] |
*[http://www.aaisp.net.uk/kb-broadband-ipv6.html www.aaisp.net.uk/kb-broadband-ipv6.html] |
||
| Line 15: | Line 15: | ||
*Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem |
*Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem |
||
*Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem [[ |
*Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem [[IPv6 SpeedTouch|Guide]] |
||
*Netgear DG834v2 running OpenWRT 8.09 (Kamikaze) |
*Netgear DG834v2 running OpenWRT 8.09 (Kamikaze) |
||
*Linksys WRTU54G-TM running OpenWRT trunk build with a Netgear DM111P Modem |
*Linksys WRTU54G-TM running OpenWRT trunk build with a Netgear DM111P Modem |
||
Revision as of 00:00, 18 August 2018
Related Pages on the A&A Website
Useful Blog/HOWTO Entries
- Using OpenWRT as an IPv6 router
- Configuring OpenWRT for IPv6
- IPv6 Source Address Selection on Linux
- Linux/BSD Configuration commands
IPv6 ready hardware
The following equipment has been successfully used as an IPv6 Router for home use. These are known as CPE or Customer Premises Equipment.
- Linksys NSLU2 running OpenWRT 10.03 (Backfire) with a Netgear DM111P ADSL2+ DSL Modem
- Linksys NSLU2 running Debian Squeeze with a SpeedTouch USB ADSL modem Guide
- Netgear DG834v2 running OpenWRT 8.09 (Kamikaze)
- Linksys WRTU54G-TM running OpenWRT trunk build with a Netgear DM111P Modem
- Netgear WNR854T running OpenWRT 10.03 (Backfire) with BT Openreach modem on FTTC
- Cisco Devices running 12.4 and above
- Our FireBrick 2700 page has info on Native IPv6 config (also applies to 2500)
- Vigor 120 - earlier firmware versions have problems with IPv6
- Billion BiPAC 7800N with firmware 1.06d
- The MikroTik RouterOS page has information on IPv6 configuration
The search for additional IPv6 CPE possibilities: IPv6CPESearch
- Juniper SRX series of routers
Native IPv6 Connections
- Cisco IPv6 Native Config
- IPv6 - How AAISP manage IPv6 on Broadband lines.
IPv6 over IP Tunnelled Connections
- Cisco IPv6 Tunnel Config
- FreeBSD IPv6 Tunnel Config
- FireBrick 2700 v6 Tunnel
- Debian IPv6 Tunnel Config
- Linux NetworkManager IPv6 Tunnel Config
See also the configuration examples on the IPv6 Knowledge-base page referenced above.
FireBrick 2500/2700
It's quite easy.... Assuming you have an IPv6 block allocated to your line on Clueless and you're using the FB for PPPoE, then all the FB config needs is:
- An IPv6 address on the LAN subnet
- ra="true" in the subnet