Router - VyOS

VyOS is an Open Source router operating system built on top of Debian Linux. Rather than having to configure lots of different software packages, everything is control through a single configuration file and it uses a command-line based configuration interface, similar to Juniper's JunOS. It is based on Vyatta (as is Ubiquiti's EdgeOS).

Documentation for VyOS is available here: https://vyos.readthedocs.io/en/latest/

Hardware

VyOS runs on standard x86 PC hardware (note that version 1.2+ requires 64-bit hardware).

• PC Engines APU2 is x86 hardware with 2-4 network interfaces, with rack-mount enclosures available
• Old Thin Clients on eBay can make cheap routers, as most are fan-less and come with flash storage
• More in the VyOS 'bare metal' documentation

Installing

VyOS is open source (available on GitHub), however the stable (Long Term Support) releases (with a version number) are only available with a very expensive subscription.

Rolling releases, built nightly, are available for free and can be downloaded here: https://downloads.vyos.io/?dir=rolling/current/amd64

After downloading an ISO, copy it on to a USB drive (I used Etcher) and then boot off the USB drive to run the install image command. Full install instructions here: https://vyos.readthedocs.io/en/latest/install.html

Configuring network Interfaces

TBC

Configuring PPPoE

TBC

Example Configuration

interfaces {
    ethernet eth0 {
        description LAN
        address 192.168.1.1/24
        address 2001:8b0:xxxx::1/64
        ipv6 {
            router-advert {
                send-advert true
                prefix 2001:8b0:xxxx::/64 {
                }
            }
        }
    }
    ethernet eth1 {
        description WAN
        duplex auto
        speed auto
        pppoe 0 {
            default-route auto
            enable-ipv6
            ipv6 {
                address {
                    autoconf
                }
            }
            mtu 1492
            name-server auto
            user-id mxxx@a.1
            password ****************
        }
    }
    loopback lo {
    }
}
nat {
    source {
        rule 100 {
            description "NAT for IPv4 on LAN"
            outbound-interface pppoe0
            source {
                address 192.168.1.0/24
            }
            translation {
                address masquerade
            }
        }
    }
}
protocols {
    static {
        interface-route6 ::/0 {
            next-hop-interface pppoe0 {
            }
        }
    }
}
service {
    dhcp-server {
        shared-network-name LAN {
            authoritative
            subnet 192.168.1.0/24 {
                default-router 192.168.1.1
                dns-server 217.169.20.20
                dns-server 217.169.20.21
                domain-name example.com
                lease 86400
                range 0 {
                    start 192.168.1.100
                    stop 192.168.1.200
                }
            }
        }
    }
    ssh {
        port 22
    }
}
system {
    config-management {
        commit-revisions 100
    }
    console {
        device ttyS0 {
            speed 115200
        }
    }
    host-name vyos
    login {
        user vyos {
            authentication {
                encrypted-password ****************
                plaintext-password ****************
            }
            level admin
        }
    }
    ntp {
        server time.aa.net.uk {
        }
        server 0.uk.pool.ntp.org {
        }
        server 1.uk.pool.ntp.org {
        }
    }
    syslog {
        global {
            facility all {
                level info
            }
            facility protocols {
                level debug
            }
        }
    }
}