L2TP Client: OpenWRT with Policy Based Routing

This guide was kindly written by Alan T on 04/04/2024

1. Configure LAN interface

Click Add new interface, select Static address then enter

Device br-lan

IPv4 address 10.0.0.1 or 192.xxx.x.x

IPv4 netmask 255.255.255.0

Firewall Settings lan

DHCP Sever On

Click Save & Apply, then disconnect your WLAN connection and rejoin, or refresh IP address.

2. Set up WAN Connection

This is depended on your WAN connection; however you will most likely need to connect to it wirelessly in Client mode :like myself, or create a DHCP client on eth0.2 (VLAN 2) interface which should default to untagging VLAN 2 on the WAN :interface.

In most situations you should probably enable Masquerading on the WAN interface (default) which is found under Firewall.

3. Create LAN Access Point(s) & add security

As above, in my case I have set up MyNetwork_5Ghz & MyNetwork_2Ghz, and have secured with a Passphrase. BOTH :interfaces are bound to the default br-lan interface which defaults to VLAN 1 (eth0.1) which untags ALL LAN ports.

You can change this as you wish.

4. Download and Install xl2tpd

Go into Software, click Update lists, and then search for xl2tpd, and then click to install.

In my case I have already installed it, however a reboot will be required one you have installed it.

5. Configure AAISP L2TP Connection.

Interfaces, Add new interface, select L2TP, and enter your login details, and information as shown below.

The metric and DNS weight aren’t particularly important here for simple policy routing; however, these will be :required later on.

I have set my WAN interface up with metric 2, and DNS weight 3.

Use default gateway also selected.

6. MWAN3 Package – Policy Based Routing Installation.

Same as installing xl2tpd really, except that you will want to install mwan3, and the luci snap in for it.

7. MWAN3 configuration.

Network -> MultiWAN Manager

The Name MUST match exactly to the interface names for your L2TP connection, and you’re your other WAN connections. If :set correctly, then the Metric should be pulled from the interface.

Set Ping, and enter something to ping. A couple of public DNS servers should work nicely. Everything else defaults.

Ignore everything else, except that you will want to edit the wan_m1_w3, and wan_m2, w3, and select your interfaces as :specified in MWAN3 interfaces.

Under policy, create two new policies, and add AAISP_ONLY, or VPN_ONLY, or TUN_ONLY, and then pop wan_m1_w3 into it, :and do the same for your WAN connection selecting wan1_m2_w3. In my case I have sky broadband so I created a WAN :interface called SKY, and refer to my internet connection as SKY, or SKY_ONLY

Rules are pretty simple, and are run from top bottom sequentially. In my case I want to send everything on my network :directly over Sky unless it’s a server. I set up iPad & Laptop so that I could switch between AAISP/SKY to test :external IP with http://ip.help.me.uk.

This configuration works a treat!

8a. Ports Forwards.

Last thing to do is to configure Port forwards to your server, and your running services. In my case I am running a :LAMP server on my network, and the same server hosts the DNS for my domain, and I am also running a Postfix/ Dovecot :server for Mail.

I also run a small Docker cluster (IPVLAN 10.0.1.0/24) for playing with, and in this case I am forwarding TCP 1080 to :one of my containers running Apache on TCP 80.

8b. Firewall Configuration for Port Forwards

I have been a little lazy with my firewalling, however providing there isn’t a port forward in place, then the ports :won’t be exposed.

The Luci from Sky rule allows me to administer the OpenWrt config from the shared sky service, which is a good :fallback if you accidentally screw your LAN config.

I think that’s about it. I haven’t created any special routes for the L2TP service, since OpenWRT automatically sets :them up, which is really nice.

Save your config!