Back up to the Technicolor_DGA0122 Page

Difference between revisions of "DGA0122 Public IPs"

From AAISP Support Site
Jump to: navigation, search
[quality revision][quality revision]
m
m
 
Line 21: Line 21:
 
Staff can re-configure the LAN subnet via our TR-069 programming - this can be used if you change your block of IPs or if you want to change from using private IPs (192.168.1.1) to public ones
 
Staff can re-configure the LAN subnet via our TR-069 programming - this can be used if you change your block of IPs or if you want to change from using private IPs (192.168.1.1) to public ones
   
Another work around is to set up the router for dual LAN subnets - that is to have the private IPs as well as the Public Subnet.
+
Another work around is to set up the router for dual LAN subnets - that is to have the private IPs as well as the Public Subnet. See: [[DGA0122 Dual LAN Subnets]]
 
===Dual LAN Subnets===
 
Desired outcome: You want the router to have a main NAT's IP block and allocate IPs by DHCP to your LAN, but you want an additional public subnet which you can use on specific devices on your LAN that you configure manually.
 
 
Prerequesits: The router would be in a state where it is configured initially without the public block of IPs - ie, it's has the private IPs on the LAN. Then, the IP block can be allocated to your line and some manual configuration can be applied to the router as follows:
 
 
[[File:DGA-System-Info.png|thumb|System Menu]]
 
[[File:DGA-Setup-Gateway-Button.png|thumb|Setup your Gateway button]]
 
[[File:DGA-Routed-Subet-tab.png|thumb|Routed Subnet tab]]
 
[[File:DGA-RoutedSubetSettings.png|thumb|Routed Subnet settings]]
 
 
 
# Go to gateway tile / System Info (top left)
 
# Click 'Configuration' and then click 'setup your gateway'
 
# Click 'Advanced', then click the 'Routed Subnet' tab
 
# Here set:
 
## Firewall setting
 
## disable 'In Range WAN IP'
 
##Set the the Gateway Address to be the first usable IP in your block
 
##Select the correct subnet mask
 
##Click Save
 
#you should now be able to statically configure the IP address settings on your devices using the IPs available in your block.
 
 
Note:
 
*DHCP will use the private IPs, it's not possible to change it.
 
*Sending a config from the A&A control pages will overwite these changes.
 

Latest revision as of 20:00, 30 March 2021


Unable to set or change the LAN address when using public IPs

  • Date reported 2020-12-08
  • Software Version 19.4 (19.4.0207-4381030)
  • Status: With Technicolor

If you want to set the Local Network IP address via the web interface to a public IP then you will get the error 'Cannot use an address in this address range' and will be unable to change it.

It seems the web interface only allows RFC1918 addresses to be used as the 'Local IPv4 Address'

However, when A&A program the router via TR069, it is possible for it to be configured with a public subnet.

This bug only affects you if you want to change the Local IPv4 Address to a public IP yourself, via the web interface.

Workaround

Staff can re-configure the LAN subnet via our TR-069 programming - this can be used if you change your block of IPs or if you want to change from using private IPs (192.168.1.1) to public ones

Another work around is to set up the router for dual LAN subnets - that is to have the private IPs as well as the Public Subnet. See: DGA0122 Dual LAN Subnets