Search results

...Customers, please run the speed tester at [http://internet-speedtest.net/ internet-speedtest.net] (and submit your line number once complete). Please run this

...outers web and telnet interfaces, by either disabling access from the WAN (Internet) altogether, or by restricting access by IP address. These settings are mad nat ifconfig intf=Internet translation=disabled

#Congestion somewhere between the premises and the internet causing slow-downs # '''Connect directly in to the ONT''' <br> It's possible to use the internet without the use of the router. You can connect your computer directly in to

...ve sky broadband so I created a WAN :interface called SKY, and refer to my internet connection as SKY, or SKY_ONLY

...D -i DEV_LAN -o pppoe-AA_1 -m comment --comment "Allow traffic from LAN -> internet" -j ACCEPT ...D -i DEV_LAN -o pppoe-AA_2 -m comment --comment "Allow traffic from LAN -> internet" -j ACCEPT

...r PPPoE capable router will plug in to the LAN port and connect you to the internet.

...nections which can be via multiple ADSL lines that are even from different internet providers.

...dafone SIM, the username was web, the password was web, and the APN was pp.internet. {Administrator}=&gt;:ppp iflist intf=Internet

*MTU 1500 is not supported on some setups (Internet access will still work fine, but we'd like 1500) - (ZyXEL will not provide ...n to the ZyXELs own web interface when trying to access a website when the internet connection is down, this applies for http and https traffic. This is not a

| Log || Configure Local logging || Logs: System, PPPoE, XDSL, Internet, Attack, Account. || 2015-05-29

When in bridge mode the ZyXEL router will not have access to the internet itself, and so won't have a way to upgrade in this state. To upgrade you ne

...ng your Firebrick to a .css file that is stored in a website on the public Internet might, in theory at least, have security implications. Certainly review sec ...lling in an evil .css file is an open question. Some versions of Microsoft Internet Explorer for Windows could cause code to be executed when ''triggered from

*''Basic Settings'', ''Internet Protocol'', select ''Both, prefer IPv6'' (or, if you're brave, select ''IPv

At this point you should be able to browse the internet and connect to the Vigor. The PPPoE interface should have the /32 address

Some devices I have allow all IP addresses to control them, but also need internet access for some functionality

...does not support IPv6, so this seems safe. IPv6 is the current version of internet protocol so it seems odd that it is disabled by default.

** '''Solid Green''': Internet service has been established

...Server Only --> Set to Enabled (This stops direct 'ghost calls' from the internet, and only allows calls from the registered SIP server)

You'll probably also want to ensure your LAN is protected from the big bad internet by a firewall. I did this by including two files in /etc/network/if-up.d/.

You can also try connecting to the Internet with just a PC plugged in to the Openreach modem. This will eliminate the r

Service list: INTERNET

#Control panel, Network and Internet

...uthentication. This involves sending your username and password across the internet to our servers. This should be done with TLS enabled as otherwise your cred

* At present the data makes use of a NAT Internet connection which is unfiltered. We hope to have a more direct APN in due co

A 1500 MTU is important because there are many networks and hosts out on the internet which are poorly configured and block all ICMP packets in an attempt to gai

There is very limited information on the internet on how to configure a Juniper SRX router use IPv6 over PPPoE, so I have wri

...or DHCP, whatever you want, doesn't matter, that's just to get you on the internet so we can set up L2TP and route IPs through that.

...he IP of our LNS, as that is the 'next hop' on the customer's route to the internet.

...l be used as the default route, saving this config should mean you have an internet connection!