Status Tests: Difference between revisions

From AAISP Support Site
mNo edit summary
mNo edit summary
Line 19: Line 19:
Down Sync=6144Kb/s FTB LoopLoss=33dB SNR=10dB ErrSec=0 HECErr=0 Cells=-1335203176
Down Sync=6144Kb/s FTB LoopLoss=33dB SNR=10dB ErrSec=0 HECErr=0 Cells=-1335203176
</pre>
</pre>
This one shows that the line has a FTB - Fault Threshold Breach - ie, the Down Sync (6,144) is less than the Fault Threshold Rate (6,374). The line speed is below what it should be and would need looking in to. See: [[:Category:Slow_ADSL]]
This one shows that the line has a '''FTB''' - Fault Threshold Breach - ie, the Down Sync ('''6,144''') is less than the Fault Threshold Rate ('''6,374'''). The line speed is below what it should be and would need looking in to. See: [[:Category:Slow_ADSL]]





Revision as of 09:03, 10 March 2015

BT Sync Status Test

  • Available on BT ADSL lines.

This will report back the current sync status of the line, including error counts. This is non-intrusive and should not cause the line to drop.

Example output:

BT Test xDSL Status Check:Pass Standalone sub test passed successfully. Pass OK. Circuit In Sync.
BRAS=5779kbit/s FTR=6502kbit/s MSR=8128kbit/s ServOpt=1 I/L=A
Up Sync=854kbit/s LoopLoss=22.6 dB SNR=17.5 dB ErrSec=0 HECErr=0 Cells=1677609
Down Sync=6551kbit/s LoopLoss=40.8 dB SNR=13.5 dB ErrSec=0 HECErr=N/A Cells=4001712

This shows the line is In Sync, with an Up Sync of 854Kb/s, and a Down Sync of 6551Kb/s.

BT Test xDSL Status Check:Pass OK.pass OK. Circuit In Sync
BRAS=5000Kb/s FTR=6374Kb/s MSR=7968Kb/s ServOpt=1 I/L=A
Up Sync=448Kb/s LoopLoss=21dB SNR=24dB HIGH ErrSec=0 HECErr=0 Cells=928584990
Down Sync=6144Kb/s FTB LoopLoss=33dB SNR=10dB ErrSec=0 HECErr=0 Cells=-1335203176

This one shows that the line has a FTB - Fault Threshold Breach - ie, the Down Sync (6,144) is less than the Fault Threshold Rate (6,374). The line speed is below what it should be and would need looking in to. See: Category:Slow_ADSL


FTTC End to End Test

  • Available on BT FTTC/FTTP lines.

This will run FTTC/FTTP specific tests and will suggest if it finds a fault or not.

Example result:

BT Test E2E Access Test/DCN:Inconclusive OR test pass. Unable to find the fault.
Down:40.0 (39.7/39.9/40.0) Up:10.0 (9.9/9.9/9.9)
NA 0.128M-40M Downstream, Interleaving Off - 0.128M-10M Upstream, Interleaving Off.
In Sync Pass:GTC_FTTC_SERVICE_0000 GEA service test completed and no fault found.

If the test says...

Down:40.0 (//) Up:10.0 (//)

...then the line is probably not in sync (no sync figures given).