...ay to configure the router to only NAT the private IP addresses and not to NAT the public IP addresses.
...e 'Port Forwarding' AND 'Address Mapping' features. These are found in the NAT section of the web interface.
2 KB (436 words) - 11:26, 7 October 2020
#REDIRECT [[Router - Technicolor - Mixed NAT]]
46 bytes (7 words) - 21:59, 4 June 2013
...a router or firewall which does some sort of Network Address Translation (NAT). This page tries to explain some of the issues, and why it is often a prob
...icially supported, but generally can be made to work. Due to the nature of NAT, and the numerous implementation and 'fixes' and 'bodges' in routers, it ca
17 KB (3,117 words) - 08:45, 30 January 2024
#REDIRECT [[Router - TG582N - Mixed NAT]]
41 bytes (8 words) - 08:40, 18 June 2013
local network such that one subnet gets its addresses translated by NAT and the other
Mixed NAT is not recommended, far better to use a real
5 KB (788 words) - 00:03, 18 August 2018
If there is no NAT involved, you need:
If NAT has been detected, or you force IKE to believe NAT is present (see below) you need:
2 KB (304 words) - 23:59, 17 August 2018
#REDIRECT [[Router - Technicolor - Mixed NAT]]
46 bytes (7 words) - 21:59, 4 June 2013
#REDIRECT [[Router - TG582N - Mixed NAT]]
41 bytes (8 words) - 08:40, 18 June 2013
At the moment the dataservice is NAT'd, but unfiltered.
110 bytes (17 words) - 13:10, 6 March 2015
...ay to configure the router to only NAT the private IP addresses and not to NAT the public IP addresses.
...e 'Port Forwarding' AND 'Address Mapping' features. These are found in the NAT section of the web interface.
2 KB (436 words) - 11:26, 7 October 2020
**Network Setting - NAT - ALG
(On older models/firmware the command to use is '':nat unbind...'' rather than '':connection unbind...'')
2 KB (358 words) - 14:17, 28 August 2019
=== Enabling/Disabling NAT ===
To view NAT status:
4 KB (563 words) - 00:18, 18 August 2018
local network such that one subnet gets its addresses translated by NAT and the other
Mixed NAT is not recommended, far better to use a real
5 KB (788 words) - 00:03, 18 August 2018
...router from Solwise works well with our data SIMS. The router supports No NAT is so is able to use our routed IP blocks on 3G data SIMS.
284 bytes (49 words) - 13:03, 6 March 2015
!NAT Tested
!NAT HElper
2 KB (314 words) - 12:56, 17 March 2022
Set the NAT flag on the ipsec roaming pool definition.
the roaming pool NAT setting should not be set. Normally you
6 KB (970 words) - 07:49, 28 July 2023
nat mapadd intf=Internet type=nat outside_addr=80.2.2.0/28 inside_addr=80.2.2.0/28
1 KB (202 words) - 00:19, 18 August 2018
nat=no...
1 KB (51 words) - 08:42, 20 May 2015
...ROroute H820' router works well with our Data SIMS. The router supports no NAT, and is specified to be more of an 'industrial' device.
486 bytes (76 words) - 13:03, 6 March 2015
...th everything necessary to do PPPoE, mini jumbo frames, firewalling, DHCP, NAT, IPv6 RA, DNS Caching and 6to4/DNS64 if you need it.
...tion (/etc/pf.conf) to enable NAT (replace the range with your chosen IPv4 NAT range):
2 KB (398 words) - 00:17, 18 August 2018
=== If you are not using public IP addresses (ie NAT): ===
...he new call server (e.g. FireBrick FB2900 and many simple NAT routers). If NAT works, then well done, but if not we cannot guarantee to be able to make it
7 KB (1,042 words) - 10:08, 12 April 2024
The TL-WR741ND router works, although it can only do NAT, but is very cheap.
467 bytes (72 words) - 00:02, 18 August 2018
...andset loose cable?! Firewall/NAT blocking traffic || Investigate firewall/NAT/ALG
...a few minutes''' || Firewall/NAT/session timeouts || Investigate firewall/NAT/ALG
5 KB (927 words) - 20:58, 14 July 2023
...and either public Legacy IPv4 addresses on the LAN, or private address and NAT on the FireBrick. In either case you can have public IPv6 addresses on the
...nterlink address block could be private IPv4 addresses but you do not want NAT or fire-walling on the external routers even in that case as it will not ha
1 KB (241 words) - 09:26, 19 March 2018
...o LANs, e.g., this will allow all traffic to and from Reading and will not NAT the traffic:
<rule name="Allow" set-graph="IPSecTraffic" action="accept" set-nat="false" />
3 KB (399 words) - 23:59, 14 March 2017
