Category:Technicolor DGA0122: Difference between revisions

Back up to the A&A Routers Page
From AAISP Support Site
mNo edit summary
mNo edit summary
Line 62: Line 62:


==Bugs & workarounds==
==Bugs & workarounds==
We've identified a couple of bugs and have listed them here:
Sadly, CPE has always had some quirks or bugs. We've identified a couple of problems with the DGA0122 and have listed them here:
*[[DGA0122_Public_IPs|Unable to set or change the LAN address when using public IPs]]
*[[DGA0122_Public_IPs|Unable to set or change the LAN address when using public IPs]]
*[[DGA0122_CQM_Graphs_Show_Latency|CQM graphs show latency spikes]]
*[[DGA0122_CQM_Graphs_Show_Latency|CQM graphs show latency spikes]]
*[[DGA0122_No_IPv6|IPv6 seemingly enabled, but not actually working]]



[[Category:AA Routers]]
[[Category:AA Routers]]

Revision as of 19:21, 29 September 2021


Technicolor DGA0122
Technicolor DGA0122 ports
Technicolor DWA0120 ports
DGA0122 Ports
DWA0120 Ports
DGA0122 Inside
Example default serial sticker

These pages are about the DGA0122 and the DWA0120. These two routers are similar, the main difference being that the DGA0122 does not have the analogue phone ports for VoIP.

DGA0122 and DWA0120

AAISP started selling the DGA0122 in December 2020. Supply problems (Due to Brexit) did mean a lack of stock in January 2021 and the DWA0120 was supplied as an alternative. The two are similar, so rather than having separate pages for the two models, we're combining the information for both here.

Notable Differences:

Basic Specs

  • 4x 10/100M/1,000M ports.
  • Modem supports VDSL (FTTC) and ADSL/ADSL2+ (Not G.Fast)
  • WiFi is:
    • 2.4GHz WiFi-4, (2x2) IEEE 802.11n
    • 5GHz, WiFi-5, (3x3) IEEE 802.11ac
  • 2 FXS ports, for connecting an analogue phone to a VoIP account DGA0122 only

User information

Suitable for:

  • ADSL1, ADSL2+
  • VDSL (FTTC)
  • G.Fast - using the Ethernet WAN port connected to an existing G.FAST modem
  • FTTP, FTTPoD - using the Ethernet WAN port to the fibre termination 'modem'

Bridge mode: The automatic A&A configuration will not configure these routers as 'bridge'. If you want to use your own PPPoE router. In this case our basic ZyXEL is a better choice, or you can configure it manually: https://support.aa.net.uk/DGA0122_Bridge_Mode

Admin and WiFi passwords

We ship the router with a basic configuration which is just enough to get the router to log in to us and fetch its full configuration for your line. There are settings on the control pane which can set the SSID, passwords etc, but until the router has been sent its full configuration it is in an 'unconfigured' state.

As shipped / unconfigured Once configured
IP: 192.168.1.1 192.168.1.1 or your public block
Username: admin (or engineer for some superpowers)
Password: as stated on the rear panel as printed on the A&A card
Wifi Name:
WiFi Password:

Bugs & workarounds

Sadly, CPE has always had some quirks or bugs. We've identified a couple of problems with the DGA0122 and have listed them here:

Media in category 'Technicolor DGA0122'

The following 9 files are in this category, out of 9 total.

Retrieved from ‘http://support.aa.net.uk/index.php?title=Category:Technicolor_DGA0122&oldid=15342’