Category:Technicolor DGA0122: Difference between revisions

Revision as of 09:18, 13 July 2022

Technicolor DGA0122

Technicolor DGA0122 ports

Technicolor DWA0120 ports

DGA0122 Ports

DWA0120 Ports

DGA0122 Inside

Example default serial sticker

These pages are about the DGA0122 and the DWA0120. These two routers are similar, the main difference being that the DWA0120 does not have the analogue phone ports for VoIP.

DGA0122 and DWA0120

AAISP started selling the DGA0122 in December 2020. Supply problems (Due to Brexit) did mean a lack of stock in January 2021 and the DWA0120 was supplied as an alternative. The two are similar, so rather than having separate pages for the two models, we're combining the information for both here.

Notable Differences:

DGA0122 has two analogue telephone ports (ATA) for VoIP support

Basic Specs

4x 10/100M/1,000M ports.
Modem supports VDSL (FTTC) and ADSL/ADSL2+ (Not G.Fast)
WiFi is:
- 2.4GHz WiFi-4, (2x2) IEEE 802.11n
- 5GHz, WiFi-5, (3x3) IEEE 802.11ac
2 FXS ports, (ATA) for connecting standard analogue phone devices to a VoIP account DGA0122 only

User information

Spec sheet: File:DGA0122 v1.2 public.pdf
A&A Quick Start sheet File:DGA0122 Quick Start.pdf

Suitable for:

ADSL1, ADSL2+
VDSL (FTTC)
G.Fast - plug Ethernet WAN port connected to an existing G.FAST modem
FTTP, FTTPoD - plug Ethernet WAN port to the fibre termination 'modem' - suitable for 1G/s FTTP (see note on speeds)

Bridge mode: The automatic A&A configuration will not configure these routers as 'bridge'. If you want to use your own PPPoE router. In this case our basic ZyXEL is a better choice, or you can configure it manually: https://support.aa.net.uk/DGA0122_Bridge_Mode

Speeds

This router can be used with faster FTTP circuits, eg up to 1Gb/s. Throughput on wifi will be limited to much lower speeds, but devices connected using wired connections should see around 950 Mbps when using our speed tester.

Admin and WiFi passwords

We ship the router with a basic configuration which is just enough to get the router to log in to us and fetch its full configuration for your line. There are settings on the control pane which can set the SSID, passwords etc, but until the router has been sent its full configuration it is in an 'unconfigured' state.

	As shipped / unconfigured	Once configured
IP:	192.168.1.1	192.168.1.1 or your public block
Username:	admin (or engineer for some superpowers)
Password:	as stated on the rear panel	as printed on the A&A card
Wifi Name:
WiFi Password:

Bugs & workarounds

Sadly, CPE has always had some quirks or bugs. We've identified a couple of problems with the DGA0122 and have listed them here:

Pages in category 'Technicolor DGA0122'

The following 16 pages are in this category, out of 16 total.

D

Media in category 'Technicolor DGA0122'

The following 9 files are in this category, out of 9 total.

A3 DGA0122 setupguide.pdf ; 2.92 MB
DGA0122 Quick Start.pdf ; 1.07 MB
DGA0122-Engineer-Front-Page.png 1,620 × 1,488; 370 KB
DGA0122-Firewall-Page-User-Defined-rules.png 1,568 × 1,312; 205 KB
DGA0122-Firewall-Page.png 1,568 × 766; 86 KB
DGA0122-front-page.png 2,386 × 1,432; 425 KB
DGA0122-Local-Network-Page.png 1,572 × 1,024; 125 KB
DGA0122-PPP-Page.png 1,574 × 998; 115 KB
DGA0122-WiFi-Page.png 1,574 × 1,312; 201 KB

@@ Line 1: / Line 1: @@
 __NOTOC__<indicator name="Front">[[File:Menu-B10C.svg|link=:Category:AA_Routers|30px|Back up to the A&A Routers Page]]</indicator>
-These pages are about the DGA0122 and the DWA0120. These two routers are similar, the main difference being that the DGA0122 does not have the analogue phone ports for VoIP.
-==DGA0122 and DWA0120==
-AAISP started selling the DGA0122 in December 2020, but supply problems (Due to Brexit) has meant a lack of stock. As of January 2021 AAISP have some stock of DWA0120 which are similar, so rather than having separate pages for the two models, we're combining the information for both here.
-'''Differences:'''
-*DGA0122 has two analogue telephone ports for VoIP support
-*DGA0122 has WiFi an auto band jumping option
-[[File:DGA0122-rear.png|200px|thumb|Technicolor DGA0122 ports]]
 [[File:DGA0122-front.jpg|200px|thumb|Technicolor DGA0122]]
+[[File:DGA0122-rear.png|200px|thumb|Technicolor DGA0122 ports]]
+[[File:DWA0120-rear.png|200px|thumb|Technicolor DWA0120 ports]]
 [[File:Rear-Drawing.png|200px|thumb|DGA0122 Ports]]
+[[File:DWA0120-ports.png|200px|thumb|DWA0120 Ports]]
 [[File:DGA0122-inside.png|200px|thumb|DGA0122 Inside]]
+[[File:Technicolor-serial-label.jpg|200px|thumb|Example default serial sticker]]
+These pages are about the DGA0122 and the DWA0120. These two routers are similar, the main difference being that the DWA0120 does not have the analogue phone ports for [[DGA0122_VoIP|VoIP]].
+==DGA0122 and DWA0120==
+AAISP started selling the DGA0122 in December 2020. Supply problems (Due to Brexit) did mean a lack of stock in January 2021 and the DWA0120 was supplied as an alternative. The two are similar, so rather than having separate pages for the two models, we're combining the information for both here.
+'''Notable Differences:'''
+*DGA0122 has two analogue telephone ports (ATA) for [[DGA0122_VoIP|VoIP support]]
 ==Basic Specs==
 *4x 10/100M/1,000M ports.
 *Modem supports VDSL (FTTC) and ADSL/ADSL2+ (Not G.Fast)
 *WiFi is:
 **2.4GHz WiFi-4, (2x2) IEEE 802.11n
 **5GHz, WiFi-5, (3x3) IEEE 802.11ac
-*2 FXS ports, for connecting an analogue phone to a VoIP account '''DGA0122 only'''
+*2 FXS ports, (ATA) for connecting standard analogue phone devices to a [[DGA0122_VoIP|VoIP account]] '''DGA0122 only'''
 ==User information==
@@ Line 29: / Line 32: @@
 *ADSL1, ADSL2+
 *VDSL (FTTC)
-*''G.Fast''  - using the Ethernet WAN port connected '''to an existing G.FAST modem'''
+*''G.Fast'' - plug Ethernet WAN port connected '''to an existing G.FAST modem'''
-*''FTTP, FTTPoD'' - using the Ethernet WAN port '''to the fibre termination 'modem''''
+*''FTTP, FTTPoD'' - plug Ethernet WAN port '''to the fibre termination 'modem'''' - suitable for 1G/s FTTP (see note on speeds)
-Not usable as a 'bridge' or 'modem' if you want to use your own PPPoE router. In this case our basic ZyXEL is a better choice.
+'''Bridge mode:''' The automatic A&A configuration will not configure these routers as 'bridge'. If you want to use your own PPPoE router. In this case our basic ZyXEL is a better choice, or you can configure it manually: https://support.aa.net.uk/DGA0122_Bridge_Mode
+===Speeds===
-==Factory Default Admin Username/Password==
+This router can be used with faster FTTP circuits, eg up to 1Gb/s. Throughput on wifi will be limited to much lower speeds, but devices connected using wired connections should see around 950 Mbps when using our speed tester.
-{|class="wikitable"
-!colspan="3"|Default/Factory Password
+==Admin and WiFi passwords==
+We ship the router with a basic configuration which is just enough to get the router to log in to us and fetch its full configuration for your line. There are settings on the control pane which can set the SSID, passwords etc, but until the router has been sent its full configuration it is in an 'unconfigured' state.
+{|class="wikitable" style="text-align:center;
+!
+!As shipped / unconfigured
+!Once configured
 |-
 !IP:
+|192.168.1.1
-|colspan="2"|192.168.1.1 (will change once configured if you have a block of IPv4 addresses)
+|192.168.1.1 or your public block
 |-
 !Username:
-|admin (or engineer for some superpowers)
+|colspan="2" |admin (or engineer for some superpowers)
 |-
 !Password:
-|Before configured it will be as stated on the rear panel. Once configured it will be the one printed on the A&A card.
+|rowspan="3"| as stated on the rear panel
+|rowspan="3"| as printed on the A&A card
 |-
+!Wifi Name:
-!WiFi Password:
+|-
-|Before configured it will be as stated on the rear panel as 'ACCESS KEY'. Once configured it will be the one printed on the A&A card.
+!WiFi Password:
 |}
 ==Bugs & workarounds==
-We've identified a couple of bugs and have listed them here:
+Sadly, CPE has always had some quirks or bugs. We've identified a couple of problems with the DGA0122 and have listed them here:
 *[[DGA0122_Public_IPs|Unable to set or change the LAN address when using public IPs]]
 *[[DGA0122_CQM_Graphs_Show_Latency|CQM graphs show latency spikes]]
+*[[DGA0122_No_IPv6|IPv6 seemingly enabled, but not actually working]]
 [[Category:AA Routers]]