Category:Bonding: Difference between revisions

Latest revision as of 01:23, 9 October 2022

There are many ways to bond multiple lines together and there are different reasons for wanting to do this. The main reasons are extra overall speed, and added redundancy against failure. The pages below will give you information about how it works, why it's good to bond lines and how to configure routers for bonding lines.

Bonding Overview

An introduction to bonding and what benefits it can bring. Read this first to get an overview of bonding lines

IP Settings

Information about how we route IP addresses over bonded lines

Bonding for more speed

Information on how bonding can help improve upload and download speeds

Bonding for resilience

How bonding can improve resilience and reliability of your internet connection

Device Configuration

Help pages on setting up particular routers for bonding

Full Bonding with a FireBrick

A FireBrick at your side can manage bonding, fallback and firewalling - this would give you maximum benefit of having multiple lines. AAISP staff can configure a router when purchased for bonding for a nominal fee. The FireBrick pages also covers config examples for bonding on the 2500 and 2700 FireBricks

Subcategories

This category has only the following subcategory.

B

Bonding Configuration

Pages in category 'Bonding'

The following 5 pages are in this category, out of 5 total.

B

S

Simple bonding

@@ Line 1: / Line 1: @@
+__NOTOC__<indicator name="Configuring">[[File:menu-configure.svg|link=:Category:Configuring|30px|Back up to the Configuring Category]]</indicator>
-AAISP have been providing bonded ADSL services for many years... There are various things to consider and understand...
+There are many ways to bond multiple lines together and there are different reasons for wanting to do this. The main reasons are extra overall speed, and added redundancy against failure.  The pages below will give you information about how it works, why it's good to bond lines and how to configure routers for bonding lines.
+<div class="AAMenuRow">
-==Overview==
+{{AAMenu|img=Menu-information.svg|link=Bonding Information|title=Bonding Overview|text=An introduction to bonding and what benefits it can bring. Read this first to get an overview of bonding lines}}
-AAISP support per-packet bonding - this is at the IP level, and simply means that packets entering or leaving your site use the ADSL lines on a roundrobin basis (or based on the speed of the lines). That way, a single TCP/IP session is transmitted over multiple lines.
+{{AAMenu|img=Menu-network.svg|link=Bonding IP Settings|title=IP Settings|text=Information about how we route IP addresses over bonded lines}}
-There is also details on the AAISP KB page: [http://www.aaisp.net.uk/kb-broadband-bonding.html]
+{{AAMenu|img=Menu-speed.svg|link=Bonding for speed|title=Bonding for more speed|text=Information on how bonding can help improve upload and download speeds}}
+{{AAMenu|img=Menu-bonding.svg|link=Bonding for resilience|title=Bonding for resilience|text=How bonding can improve resilience and reliability of your internet connection}}
+{{AAMenu|img=Menu-cog.svg|link=:Category:Bonding Configuration|title=Device Configuration|text=Help pages on setting up particular routers for bonding}}
+</div>
+==Full Bonding with a FireBrick==
-==Advantages==
+A FireBrick at your side can manage bonding, fallback and firewalling - this would give you maximum benefit of having multiple lines. AAISP staff can configure a router when purchased for bonding for a nominal fee. The [[:Category:FireBrick|FireBrick]] pages also covers config examples for bonding on the 2500 and 2700 FireBricks
-More bandwidth, as well as resilience (having more that one line increases the probability of staying online in the event of a fault)
+[[Category:Configuring]]
-==Limitations==
-We do recommend the FireBrick 105 product for bonding, fallback, and firewalling - as of Oct 2010, this is nearing the end of it's life, and the throughput peaks at around 10-10Mb/s - so with today's faster lines, it's limit may be easily reached.
--New products are due very soon to replace the 105.
-==Download Bonding==
-'''From the Internet to you.'''
-AAISP use FireBrick FB6000 routers to manage ADSL connections. This manages the bonding of traffic from AAISP to your location.
-IP blocks (configured on Clueless) can be routed to multiple lines on your login.
-for fallback, the FB6000 will stop routing IPs down a line that is off line, and from the Control Pages you can control which lines are used.
-Speed wise, the FB6000 will route based on the speed of the line - so if you have a 10M line and a 5M line, then the traffic will be weighted correctly (ie 1/3 on the 5M line, and 2/3 on the 10M line.)
-==Upload Bonding==
-Upload bonding requires a device at your side to route IP packet up alternate lines.
-Typically a FireBrick can do this, as well as provide fallback (not using a line that is down) and firewalling. AAISP staff can also configure the Firebrick for your lines for a nominal fee.
-There are other devices that can do this, some of the Mikrotik range of routers can do this.
-=Examples=
-==Simple Download Bonding==
-This is a poor-mans bonding setup, but would be effective, but not as flexible is using additional hardware such as a Firebrick. As AAISP manage download bonding, the simplest set up is as follows:
-*You have 2 or more ADSL lines with AAISP (either BT, or BE, or a mix)
-*You have a block of IPs, big enough for your LAN
-**The first usable IP will be Router 1, the second Router 2, and the rest will be for your devices.
-*You have 2 standard ADSL routers (eg supplied by AAISP)
-**The ZyXELS can be configured to use the other router as a fallback gateway (giving some level of fallback if the ADSL goes down, this isn't configured automatically by AAISP router programming)
-*You plug the routers, and computers etc all in to the same network switch
-*You pick on of the routers IP addresses to use as the gateway on your devices (or you can set up DHCP server on one of the routers)
-**You could use one router as the gateway for half of your devices, and the other router as the gateway for the other half - thus giving some level of upload bonding
-With this setup, you wouldn't have any firewall capabilities (apart from that provided by your operating systems.)
-==Simple Download Bonding, using a router/firewall==
-If you have an existing router/firewall, then you could use this to firewall your network, and provide NAT (if that's what you want to do)
-The points are similar to the above example, with a difference on the LAN side of the ADSL routers.
-*You have 2 or more ADSL lines with AAISP (either BT, or BE, or a mix)
-*You have a block of IPs, big enough for your LAN (assuming you are not natting), and a block of IPs for the ADSL routers and your firewall.
-**The first usable IP will be Router 1, the second Router 2, and the rest will be for your firewall.
-**The LAN block will be configured as static routes in the ADSL routers to route the traffic to your firewall.
-*You have 2 standard ADSL routers (eg supplied by AAISP)
-**The ZyXELS can be configured to use the other router as a fallback gateway (giving some level of fallback if the ADSL goes down, this isn't configured automatically by AAISP router programming)
-*You plug the ADSL routers and firewall (WAN port) in to the same network switch
-*Your firewalls LAN port is connected to your main LAN switch.
-*Your firewall uses one of the routers as it's gateway
-*Your firewall can be the DHCP server, can run NAT etc for your LAN
-With this case, assuming your firewall is not able to do upload bonding, or have the ability to change which router it uses in the case of an ADSL line being down, in the event of the ADSL line that is being used for upload fails, fallback would need to be controlled manually (ie configure the firewall to use the other ADSL router as it's gateway)
-=Mixing BT and BE lines=
-AAISP BT lines and BE lines can be used for bonding, and gives even great resilience in the case of a fault in BT or a fault in BE. - as of October 2010, BE lines need to run on a reduced MTU of 1492 - and bonding will need all lines to use this reduced MTU. This is an tickbox option on the control pages though